Search

Type: Posts; User: ptscon

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Looks like you cut the bellows to remove it, that...

    Looks like you cut the bellows to remove it, that reduces difficulty by 90% :)

    You can make a simply one time tool from a piece of hardwood flooring. Cut a U shape out of it on one end, this goes...
  2. Replies
    7
    Views
    272

    Lol you must be joking, where are you pulling...

    Lol you must be joking, where are you pulling these numbers from?
  3. Thanks for the info! What's configuration and...

    Thanks for the info!

    What's configuration and what RPM were you spinning the SX4 to?
  4. Replies
    19
    Views
    869

    A bunch of possibilities, for all we know the...

    A bunch of possibilities, for all we know the person ran a canned tune and badly leaned out. Did the ski have a AFR gauge?
  5. Replies
    6
    Views
    203

    Just make sure the lumber isn't touching the pump...

    Just make sure the lumber isn't touching the pump internal components, it should rest on the pump body only.
  6. Replies
    6
    Views
    203

    Get a short piece of 4x4 lumber, drill a hole in...

    Get a short piece of 4x4 lumber, drill a hole in one end so the thread portion where the impeller goes fits in it. Hold the pump ontop of the 4x4 and hit the whole thing onto garage floor. It will...
  7. Replies
    2
    Views
    123

    You really need some kind of a tool to compress...

    You really need some kind of a tool to compress the bellows and snap on the clip. I have a piece of hardwood flooring with a U cut out at one end, that end goes over the metal hat and then I use a...
  8. Don't put it at the front like the picture above,...

    Don't put it at the front like the picture above, you want it as far back of the ski as possible. The back is where water starts to accumulate, mines right in-front of the iBR. If you have it up...
  9. Replies
    19
    Views
    869

    I run Wiseco at 0.004 with no issues, no blow by...

    I run Wiseco at 0.004 with no issues, no blow by on my et135 charger.
  10. If you're concerned then test valve clearance.

    If you're concerned then test valve clearance.
  11. Replies
    3
    Views
    143

    Umm that filter is just stuck to the gasket, they...

    Umm that filter is just stuck to the gasket, they are two separate parts, just pull it off and reuse. Definitely do not run without the filter it's what catches big chunks from getting too the oil...
  12. Replies
    90
    Views
    7,472

    At what RPM does the kawi charger go positive...

    At what RPM does the kawi charger go positive pressure? It's nice that it's a stand alone unit and can't throw crap into the motor. I don't think performance is a strong trait of the kawi setup. It...
  13. Replies
    14
    Views
    497

    I'm assuming you had the motor aligned after...

    I'm assuming you had the motor aligned after replacing the mounts?
  14. Replies
    90
    Views
    7,472

    Aren't SeaDoo and Yamaha chargers centrifugal?

    Aren't SeaDoo and Yamaha chargers centrifugal?
  15. I would not go by that, you can overshoot the...

    I would not go by that, you can overshoot the limiter if there's no load on the motor.
  16. How sure are you the ECU is really flashed beyond...

    How sure are you the ECU is really flashed beyond the stock limiter?
  17. Replies
    6
    Views
    414

    Doesn't seem unrealistic, looks like cold...

    Doesn't seem unrealistic, looks like cold weather, flash, some other mods around intake/grate/impeller, light rider, a bit of current and you'r there.
  18. Must be amazing because......

    Must be amazing because...
    http://greenhulk.net/forums/attachment.php?attachmentid=450098&stc=1

    :-x
  19. Replies
    4
    Views
    198

    There's no stuffing on T3 hull in the 80s. The...

    There's no stuffing on T3 hull in the 80s. The RXT S3 hull is the one with stuffing.
  20. Replies
    19
    Views
    869

    Stock motor? Tune? What was the piston to bore...

    Stock motor? Tune? What was the piston to bore clearance?

    The clearance was too small for the amount of expansion the pistons experienced.

    It got very lean and hot and/or the piston to wall...
  21. What you could do is drain the coolant and put...

    What you could do is drain the coolant and put some air pressure into the system. Test each cylinder by putting it BDT and taking out the spark plug to see if air is coming from it. Might help...
  22. Replies
    70
    Views
    7,200

    Your Fish Pro will be the one needing to be...

    Your Fish Pro will be the one needing to be fished out soon. Got to get that sorted out.
  23. Thread: bolts reuse

    by ptscon
    Replies
    6
    Views
    239

    Flywheel are not stretch bolts, they're just not...

    Flywheel are not stretch bolts, they're just not strong enough on the 4tecs. BRP now uses the stronger 12.9 bolts so you just have to hope they're torqued correctly :)
  24. Thread: bolts reuse

    by ptscon
    Replies
    6
    Views
    239

    Do not reuse (these are stretch bolts): head...

    Do not reuse (these are stretch bolts): head bolts, rocker bolts, connecting rod bolts

    ARP: head bolts (studs), flywheel bolts
  25. Replies
    5
    Views
    234

    There's been couple reports of the front bolt...

    There's been couple reports of the front bolt pulling through the hull on the 300s, seems to be quite rare though.

    You'll have to get that bolt area structure rebuild. Your ski is fine otherwise...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4