Search

Type: Posts; User: xlint89

Page 1 of 8 1 2 3 4

Search: Search took 5.81 seconds.

  1. There are many circuits that make up the fuel...

    There are many circuits that make up the fuel supplied with these carbs. Idle speed screw, pop off pressure, transition ports, low speed jet, high speed jet, and high speed adjustment screw.
    ...
  2. Replies
    5
    Views
    98

    You can try cleaning up the contacts at the...

    You can try cleaning up the contacts at the switch, or just get a replacement.

    ...
  3. Replies
    15
    Views
    244

    Glad you got it running. If that magneto was...

    Glad you got it running.

    If that magneto was advertised as OEM, you got a case against the seller. How about a link to it?

    As for the Genesis, you should start another thread so as to not...
  4. Replies
    6
    Views
    769

    FS - Parts one more time...

    one more time...
  5. Welcome to the Hulk 1. Did you remove the jet...

    Welcome to the Hulk

    1. Did you remove the jet pump and driveshaft from the ski and attempt turning it?

    It should turn over by hand with relative ease when heads are removed like that.

    With...
  6. Replies
    3
    Views
    106

    Here you go. 135 HP ...

    Here you go. 135 HP

    http://greenhulk.net/forums/showthread.php?t=13374&highlight=slt+785
  7. Replies
    10
    Views
    162

    yes, engine will need to come out. You will...

    yes, engine will need to come out.

    You will need a complete engine rebuild kit, not just top end.

    Only specialty tools you'll need is the flywheel puller and torque wrench.

    But first, post...
  8. Replies
    9
    Views
    143

    Randy at https://weberpower.com/ has rebuild kits...

    Randy at https://weberpower.com/ has rebuild kits for cheap. Call him and tell you need the thru hull rebuild kit for the polaris. Good guy to deal with.
  9. Replies
    10
    Views
    162

    Did you compression test with the throttle wide...

    Did you compression test with the throttle wide open? You won't get true reading with throttle closed.

    Pop the heads off and see what damage there is. If you need a new piston and cyl bore. youre...
  10. Replies
    4
    Views
    161

    What about closing the choke while you open the...

    What about closing the choke while you open the throttle? Richening the air fuel mix

    When did you rebuild the carbs? Have you checked them since then?

    Any fluid in the pulse hose by chnace?
    ...
  11. Replies
    10
    Views
    162

    Make sure you are running on all 3 cyls. It...

    Make sure you are running on all 3 cyls. It doesn't sound like you are.

    Check carb screw settings again

    Are the carbs sync'd?
  12. Replies
    3
    Views
    79

    Welcome to the world of 2 strokes. It's called...

    Welcome to the world of 2 strokes. It's called "getting on the pipe".
  13. Replies
    19
    Views
    271

    Not wiseco pistons. It's a weird place for...

    Not wiseco pistons.

    It's a weird place for that piston to fail. Normally it's around the exhaust port.

    155 PSI compression and low octane fuel may have lead to the failure.

    Cen piston...
  14. Replies
    4
    Views
    161

    Welcome to the Hulk. Water in the gas? Have...

    Welcome to the Hulk.

    Water in the gas?

    Have you rebuilt the carbs?

    Correct spark plugs gapped properly?

    Have you checked the timing while running?
  15. Replies
    19
    Views
    271

    155 is pretty high compression. If someone did a...

    155 is pretty high compression. If someone did a $2k rebuild, there's a chance they installed Wiseco pistons. Wiseco's and cold water don't mix well.

    Cold seizure is the piston expands faster than...
  16. Replies
    19
    Views
    271

    How cold is the water you're riding on? Did...

    How cold is the water you're riding on?

    Did you properly warm up the engine?

    Have you done a compression test?

    I'm thinking possibility of cold seizure
  17. Replies
    4
    Views
    74

    Take a look at your cooling hose that goes to the...

    Take a look at your cooling hose that goes to the front of the expansion pipe too. They had a problem with rubbing/wearing a hole in them.

    But yes, get your bolts installed.
  18. Welcome to the Hulk. Contact John Zigler for...

    Welcome to the Hulk.

    Contact John Zigler for GENUINE Mikuni carb rebuild kits. He owns both Rock County Jet Ski and Watcon

    https://rockcountyjetski.webs.com/

    I wouldn't ride that ski until...
  19. Replies
    19
    Views
    271

    What ski is this? Try unscrewing the gas cap...

    What ski is this?

    Try unscrewing the gas cap when this happens and see if it's creating a vacuum.
  20. A hot spot in the combustion chamber is most...

    A hot spot in the combustion chamber is most likely causing the run on. Prob your lean cyl. Fatten that carb setting up. Get all your jetting rich and pull fuel out to reach peak RPM. Going lean is...
  21. Replies
    7
    Views
    120

    Have you looked at the bottom of the fuel tank...

    Have you looked at the bottom of the fuel tank for the missing piece? That's the only place it would be.

    The one not working may be able to be repaired?

    If not, you can prob find the newer...
  22. Replies
    7
    Views
    120

    It looks like you have the old style set up. ...

    It looks like you have the old style set up.

    Why are you looking to replace them?
  23. Post #5 ...

    Post #5

    http://greenhulk.net/forums/showthread.php?t=128680&highlight=carb+sync
  24. Thread: 95 slx 780

    by xlint89
    Replies
    3
    Views
    75

    Welcome to the Hulk. The SLX was pretty much...

    Welcome to the Hulk.

    The SLX was pretty much maxed out from the factory. I suggest you do the regular maintenance to keep it reliable and enjoy it.
  25. Good info ^^^^ How about posting a pic of the...

    Good info ^^^^

    How about posting a pic of the ones you need?
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4