Search

Type: Posts; User: Myself

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    11
    Views
    508

    Seems to me that for the money, you could...

    Seems to me that for the money, you could completely overhaul both skis....learn them inside and out......and have a couple nice skis that will last many years. I have seen several times in the past...
  2. Replies
    1
    Views
    88

    FS - Parts I still have this.

    I still have this.
  3. Replies
    9
    Views
    442

    Fat bead of plain jane cheap clear silicone. They...

    Fat bead of plain jane cheap clear silicone. They come back off pretty easy. It's the Right Stuff and RTV that are a PITA.
  4. That's what I would want to see on a new...

    That's what I would want to see on a new break-in. Keep doing what your doing.
  5. Replies
    1
    Views
    269

    what's your location? Maybe that would help us...

    what's your location? Maybe that would help us point you in the right direction........also what engine?
  6. Replies
    5
    Views
    302

    I'm with Water Worx.........and both of us do...

    I'm with Water Worx.........and both of us do this for a living.

    If you can feel a bit of play on the shaft up and down and left to right, it will be just fine.
  7. Replies
    1
    Views
    88

    FS - Parts VX 1100 wiring harness freshwater

    Nice complete perfect working wiring harness for a VX. only ever in freshwater. $350 shipped in the cont. USA.
  8. I left it unhooked. You can wire it to a float...

    I left it unhooked. You can wire it to a float switch then just power it to the battery.
  9. Replies
    4
    Views
    368

    I've used the pvc/vinyl air hose several times...

    I've used the pvc/vinyl air hose several times with no issues.
  10. Replies
    8
    Views
    717

    Is it an SBT crank?? They use crap bearings and...

    Is it an SBT crank?? They use crap bearings and seals. As stated either just valve it off or do a rotary gear oil loop and fill it with thick gear lube leaving the injection part alone. That's what...
  11. Replies
    2
    Views
    226

    Most common causes on a 787 for melted exhaust...

    Most common causes on a 787 for melted exhaust parts are pisser lines on exhaust backwards or a bad regulating valve on the waterbox.

    If the compression is still good...run it. 787's are tough.
    ...
  12. Replies
    30
    Views
    1,434

    Your timing is spot on! You might possibly have a...

    Your timing is spot on! You might possibly have a bad ecm. At this point I would reassemble and try this. Get a helper, crank it while holding throttle about 1/4 open and shoot a little carb cleaner...
  13. Replies
    30
    Views
    1,434

    Ha.....actually I set a 1/4' drive ratchet...

    Ha.....actually I set a 1/4' drive ratchet extension in the hole and put the tip of the dial indicator down in the end of the extension. good enough to watch the dial move!!
  14. Thread: Gutted waterbox

    by Myself
    Replies
    126
    Views
    6,517

    Ok, so for the price, one could open the side and...

    Ok, so for the price, one could open the side and peel out all the fiberglass. Then pack it with stainless kitchen scouring pads available anywhere cheap. And have a local welder close it back up...
  15. Replies
    30
    Views
    1,434

    All I used was a regular dial indicator in the...

    All I used was a regular dial indicator in the plug hole to read tdc.
  16. Replies
    30
    Views
    1,434

    When I put my wifes '06 all back together I...

    When I put my wifes '06 all back together I culdn't get it to start without holding 1/4 throttle. I had to watch tps voltage and set the throttle cable, then we had to go run it around at the lake...
  17. Replies
    1
    Views
    167

    Have you done a tps reset and verified throttle...

    Have you done a tps reset and verified throttle opening percentage in BUDS or Candoo? The rfi needs that done and then withing 15-30 minutes ride time all is well.
  18. Thread: Gutted waterbox

    by Myself
    Replies
    126
    Views
    6,517

    I don't want to jump into the frying pan here...

    I don't want to jump into the frying pan here but, I too am not fond of the loud obnoxious exhaust. It gives peopla another reason to complain and try to ban them. You can increase flow and power...
  19. Replies
    27
    Views
    1,757

    Just added the inline checks and did nothing...

    Just added the inline checks and did nothing else. The overpressure bubbling the line was because the carb check valve was jammed up with crud. Probably contributed to killing the original top end.
  20. Replies
    27
    Views
    1,757

    I have placed the Yamaha valves inline a couple...

    I have placed the Yamaha valves inline a couple times.....no issues. In fact, I have a pic here somewhere of a marble sized bubble in an oil line. The check valve was jammed up and the oil pump just...
  21. Replies
    4
    Views
    452

    WTB - Parts Some knucklehead snapped one off. I was able to...

    Some knucklehead snapped one off. I was able to extract it and save the threads so just need to put one back in.
  22. Replies
    4
    Views
    436

    Oh no!!

    Oh no!!
  23. Replies
    4
    Views
    436

    Would love to see some engine pics of that Ultra....

    Would love to see some engine pics of that Ultra. I'll bet at 180psi that thing rips!!
  24. Replies
    2
    Views
    309

    If it's no longer available from Yamaha you'll...

    If it's no longer available from Yamaha you'll need to have one made. Any graphics shop should be able to use a high quality pic of the opposite side, flip it in the software, and print one out for...
  25. Where there's a will..........there's a way. I...

    Where there's a will..........there's a way. I have no doubt your next one will be even better. I shipped a bunch of oddball parts to Russia once. The freight was very expensive. My buyer told me...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4