Search

Type: Posts; User: raven007

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    65

    A TR1 aint gonna make it 800 hours. The old 110...

    A TR1 aint gonna make it 800 hours. The old 110 horse MR1 would do it with maintenance.
  2. Replies
    4
    Views
    85

    You have to pull the exhaust to get the engine...

    You have to pull the exhaust to get the engine out in my experience. That one bolt is a pain. I think I use a 12 point box end wrench on it if its the one I am thinking of.
  3. Replies
    2
    Views
    188

    unlike old school skis where it grounds the cdi,...

    unlike old school skis where it grounds the cdi, most modern skis have a shutdown pin on the ecm. When the lanyard is pulled it tells the ecm to kill the engine, a little while later it drops the...
  4. Replies
    1
    Views
    73

    WTB - Parts Bad stx-12f/15f ECM

    Looking for a dead ecm for stx-12f/15f. My plan is to de-pot all the epoxy off the board and reuse the connector for my standalone.
  5. i just threw up in my mouth a little. And it...

    i just threw up in my mouth a little. And it wasn't last nights whiskey.
  6. I have an early (like first year IIRC) 12f (the...

    I have an early (like first year IIRC) 12f (the "sow's ear" project boat I post about) that the entire manifold was just....gone. It was corroded so badly that the holes were plugged. And I got a 15f...
  7. Replies
    7
    Views
    223

    Keep that filter fresh! You don't want it to rust...

    Keep that filter fresh! You don't want it to rust and start leaking.
  8. The trailer should NOT be nose up. How light is...

    The trailer should NOT be nose up. How light is your trailer tongue? Tongue weight and levelness is important. If you have never had a trailer go crazy due to balance and geometry being off its hard...
  9. ^^^ this My issue with the design is the...

    ^^^ this

    My issue with the design is the replacement part is freaking expensive for what it is. I mean, I know it sounds whiney bitch of me, but that manifold should NOT cost 100+ bucks.
  10. Replies
    8
    Views
    259

    bawahahaha nailed him.

    bawahahaha nailed him.
  11. Please post up on the initial fit of the engine!...

    Please post up on the initial fit of the engine! I will dig around and see if i still have the bad stator case (I am 90% sure i tossed it tho).
  12. The head I am modding is corroded in the o ring...

    The head I am modding is corroded in the o ring area a bit.
  13. Replies
    49
    Views
    3,074

    This thread needs a part out.

    This thread needs a part out.
  14. Yep. I bought an an-6 ORB reamer. Gonna put...

    Yep.

    I bought an an-6 ORB reamer. Gonna put two low profile fittings in the head and tee them together.
  15. Thread: FX140 Pistons

    by raven007
    Replies
    4
    Views
    176

    you might need to be the first to install a...

    you might need to be the first to install a thermostat!
  16. Replies
    4
    Views
    167

    FS - Parts I honestly cant remember. It is the twin to the...

    I honestly cant remember. It is the twin to the red one you posted. I wish it was a red and white 130. But they are super rare here.
  17. Replies
    2
    Views
    117

    I'm not in the northeast, but this is as easy of...

    I'm not in the northeast, but this is as easy of a conversion as you can do. There are a couple of threads on here. If you can pull the 1200 and put it back you can do this.
  18. Thread: FX140 Pistons

    by raven007
    Replies
    4
    Views
    176

    I would use them. You have both pistons so you...

    I would use them. You have both pistons so you can measure and confirm they are the same.
  19. Replies
    12
    Views
    368

    off to the dealer! Hate to see this tho :(

    off to the dealer! Hate to see this tho :(
  20. Replies
    4
    Views
    167

    FS - Parts Will you be selling any of the 130 fuel tanks?...

    Will you be selling any of the 130 fuel tanks? Kind of wouldn't mind putting one back for my conversion.
  21. Whhhhaaaattttttt. I didnt even know this came to...

    Whhhhaaaattttttt. I didnt even know this came to lake hartwell.
  22. Replies
    1
    Views
    68

    The FX ecm is different. What part do you need?

    The FX ecm is different. What part do you need?
  23. Replies
    12
    Views
    612

    The other issue is ppl trying to tune whole hog...

    The other issue is ppl trying to tune whole hog right out of the gate and burning the engine down. You dont just plug in a standalone and spool up your nagasaki noisy boy to 30 psi and tune it.
  24. Nah. Then we will have fusion reactor gas threads...

    Nah. Then we will have fusion reactor gas threads because that's the only way the energy density will ever be there.
  25. Replies
    12
    Views
    612

    There are way better hulls that need that...

    There are way better hulls that need that powerplant.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4