Search

Type: Posts; User: TJS0712F

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Ya Steve, please do add a build thread when you...

    Ya Steve, please do add a build thread when you do this. Also if you need something small/ship-able CNC plasma cut for your project let me know. I have a 4 x 8 table in my garage/shop that I built...
  2. Good luck with your endeavor. Lack of info here...

    Good luck with your endeavor. Lack of info here will result in garbage in garbage out. Just keep throwing parts at it. You'll get it.
  3. What is the speed after he worked in it. If he...

    What is the speed after he worked in it. If he checked it what are the clearances between the wear ring and the impeller.
    And what is a "stack".
  4. Never understood why people rev the piss out of...

    Never understood why people rev the piss out of these things out of the water(no load).
    Do you red line your car in neutral.
    How many hours.
    Are you the original owner.
    Does your gauge work....
  5. Replies
    3
    Views
    165

    IG. I can't even get IG to open on my phone after...

    IG. I can't even get IG to open on my phone after they did an update last week. Junk.
  6. Replies
    37
    Views
    639

    I see you found the post I was referring to. Hope...

    I see you found the post I was referring to. Hope this helps you. Please keep us posted.
  7. Replies
    21
    Views
    540

    Typical Kawasaki pump seals go bad water...

    Typical Kawasaki pump seals go bad water ingesting destroying bearings scenario. I fixed by pump when this happened. Welded up the impeller edges and machined down to get a .008" clearance. I have an...
  8. Replies
    37
    Views
    639

    Makes no sense. This is you asking for help, not...

    Makes no sense. This is you asking for help, not a how too.
  9. Replies
    37
    Views
    639

    I just noticed this is in the FAQ and How To...

    I just noticed this is in the FAQ and How To section. Think it should be moved to the Kawi 4 stroke section. It might get more input.
  10. Replies
    37
    Views
    639

    I don't rev my machine out of the water like...

    I don't rev my machine out of the water like that. I do know after I flush it I blip the throttle pretty good to minimize water in the water box, but I don't hold the throttle there. I think mine...
  11. Replies
    37
    Views
    639

    [QUOTE=rotaryboots;3037304] Yes. I cannot find...

    Yes. I cannot find it. Maybe Smokey can find it. Not even sure if it was a 15F. However many Kawis use the same crank set up.
  12. Replies
    37
    Views
    639

    Rotaryboots, Do you have any history on this...

    Rotaryboots,
    Do you have any history on this machine. What work has been done to this thing prior to you getting it. I recall reading on here somewhere and I cannot find it now where someone had...
  13. Replies
    37
    Views
    639

    My machine right now is stuck in SLO mode. Has...

    My machine right now is stuck in SLO mode. Has been for this last two times out. My gauge is blank now. SLO mode will not give you the bouncing RPMs as you explain. Everything is smooth just not as...
  14. Replies
    37
    Views
    639

    Couple things:1: Does the gauge actually work. My...

    Couple things:1: Does the gauge actually work. My 12F guage does not and it gets stuck in SLO mode. This is the third gauge. I tried the yellow/blue wire trick and it does not work. If your gauge...
  15. Replies
    1
    Views
    137

    Grille Hitch Set up

    Made this a while back. Works great.

    http://greenhulk.net/forums/attachment.php?attachmentid=451750&stc=1
  16. Replies
    12
    Views
    284

    What have you taken off so far. I am betting the...

    What have you taken off so far. I am betting the rope is caught in the impeller. What does your username signify.
  17. Replies
    8
    Views
    314

    There are hoses that go in and out of the stator...

    There are hoses that go in and out of the stator area. By the looks of the rest of the corrosion I would think the stator area may also have issues. Get a manual and make sure the hose routing is...
  18. Replies
    12
    Views
    284

    See post #4.

    See post #4.
  19. Replies
    12
    Views
    284

    Try taking the pump out and go from that way.

    Try taking the pump out and go from that way.
  20. Something is wrong here. Don't force it. Find the...

    Something is wrong here. Don't force it. Find the source and fix it. Just turn the whole pump assembly left or right a little to line up the splines. The splines are super clean with grease on them...
  21. I would like to find a case where there was some...

    I would like to find a case where there was some damage to the thrust bearing area. Just for practice TIG it up and get it on the Bpt mill and get it to spec.
  22. That pump is fixable. Seals went bad and water...

    That pump is fixable. Seals went bad and water ingested into the bearing housing. Pretty common on these things if they are not inspected often. Same exact thing happened to me. As soon as I heard a...
  23. Replies
    62
    Views
    2,640

    EPIC...

    EPIC...
  24. Replies
    19
    Views
    565

    So with 110 hrs on it and the pump had never been...

    So with 110 hrs on it and the pump had never been apart to be checked?. You know it only takes about 20min or so to pull a pump on these things with basic hand tools. The only special tool you need...
  25. Any updates.

    Any updates.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4