Search

Type: Posts; User: toxicgun

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: Gp1200r parts

    by toxicgun
    Replies
    7
    Views
    170

    FS - Parts is the intake grate stainless or aluminum?

    is the intake grate stainless or aluminum?
  2. Replies
    13
    Views
    860

    it will technically run but not correctly at all....

    it will technically run but not correctly at all. I have personally tried it.
  3. Replies
    1
    Views
    79

    WTB - Parts standard bore?

    standard bore?
  4. Replies
    7
    Views
    239

    balance technology in livermore california does...

    balance technology in livermore california does mine.
  5. Replies
    3
    Views
    155

    Thanks, being that it is your old setup I will...

    Thanks, being that it is your old setup I will take your advise. I was planning on trying .020 but I will go with what you were doing since that was working.
  6. Replies
    3
    Views
    155

    4tec turbo guys spark plug gap question

    anything past 18psi is stumbling, I am suspecting the factory gap is too much. What are you guys running? Of course I have done new plugs and coils, doesnt seem to matter. running 11.5 currently...
  7. WTB so you want to exchange your old parts for the...

    so you want to exchange your old parts for the parts you need? Just modify the sho exhaust pipe yourself, use the rest of the 1200/1300 exhaust with it.
  8. Yep, I tried that, sucked down under boost.

    Yep, I tried that, sucked down under boost.
  9. Replies
    4
    Views
    389

    from what I recall the 2001 gp1200r was the...

    from what I recall the 2001 gp1200r was the preferred hull. Supposedly stronger and lighter. I have built two with 2001 hulls.
  10. is that kanaflex for an intake or the ducting...

    is that kanaflex for an intake or the ducting from the front vents?
  11. you need to take off the intake manifold and dump...

    you need to take off the intake manifold and dump the water out of it before starting it, at least pull an intercooler hose and see if there is water sitting in the intercooler
  12. something is wrong, how is the supercharger...

    something is wrong, how is the supercharger clutch? With stock prop my gpsho hit 78mph on first test ride, sitting on the rev limiter. Sounds like it is down on power to struggle turning a 13/20
  13. it is a great upgrade to put the aluminum solid...

    it is a great upgrade to put the aluminum solid pump instead of the 02 plastic unit. 02 and 03 were plastic and with enough thrust they swell or crack under pressure. Any 04-08ish aluminum pump...
  14. SOLD Thanks Kamikaze, I will put it to great use.

    Thanks Kamikaze, I will put it to great use.
  15. Replies
    1
    Views
    97

    WTB - Parts pm sent

    pm sent
  16. SOLD pm sent

    pm sent
  17. Replies
    4
    Views
    183

    take the power and ground to the module straight...

    take the power and ground to the module straight to the battery for testing it. Are you sure the signal wire is on the correct side of the harness, not going to the paddle wheel side? Is your gps...
  18. long beep mean not recognizing the key usually. ...

    long beep mean not recognizing the key usually. May be a dying/dead mpem
  19. are they smooth? Did you plastigauge them? if...

    are they smooth? Did you plastigauge them?
    if smooth and measure correctly then run them
  20. SOLD looking for exit nozzle with reduction rings for gpr made by Riva

    Part number from Riva was RY23040-N looks like it fits multiple skis. Anyone have a setup around they would like to sell?
  21. EFR 7163, It is a GRF kit.

    EFR 7163, It is a GRF kit.
  22. Replies
    140
    Views
    20,219

    thank you!!!!

    thank you!!!!
  23. http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=451974&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=451975&stc=1
  24. Replies
    140
    Views
    20,219

    I have a 15/22 at impros right now getting...

    I have a 15/22 at impros right now getting pitched to a 15/26 and a little setback cut. Pretty much the biggest they said that prop can pitch to safely. Next step is to install the 160mm pump and...
  25. WTB pm me if you still need it. Got an 04 I am...

    pm me if you still need it. Got an 04 I am stripping.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4