Search

Type: Posts; User: TMiller

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    29
    Views
    1,420

    Myself, I didnt care for the one piece head. If...

    Myself, I didnt care for the one piece head. If the cylinders are not all exactly the same height one would think that would create an issue. If you are looking for something brand new I guess the...
  2. Replies
    29
    Views
    1,420

    I measured the chamber on a 36cc head directly...

    I measured the chamber on a 36cc head directly next to the spark plug hole and shows about 5/8 of an inch (0.65). It is not a very precise measurement but you get the idea. These have a beefy o-ring...
  3. Replies
    29
    Views
    1,420

    That is interesting that the piston was hitting...

    That is interesting that the piston was hitting on the inner edge there. The angle on the head should be greater that the angle on the crown of the piston so the outer edge should hit first.
    Like...
  4. Replies
    29
    Views
    1,420

    I can’t remember for sure but I think gaskets are...

    I can’t remember for sure but I think gaskets are 0.010 thick so you would need 3. Again I can’t remember for sure but I think squish on the red heads are 0.055 if you add 3 head gaskets then you are...
  5. Replies
    29
    Views
    1,420

    I saw you pulled one head. Did it have an o-ring?...

    I saw you pulled one head. Did it have an o-ring? I will measure the 2 different heads tonight if I have time.
  6. Replies
    29
    Views
    1,420

    I read through your original post too quickly. I...

    I read through your original post too quickly. I didn’t realize you yourself never did a compression test. That’s where I would start so you know what you have and not trust what someone else told...
  7. Replies
    29
    Views
    1,420

    I have a complete set of R&D 36cc red heads brand...

    I have a complete set of R&D 36cc red heads brand new in package if you need a replacement. The interchangeable domes were always easier if you wanted to switch back and forth from pump gas to race...
  8. Replies
    6
    Views
    493

    FS Here is a link to ADA racing for replacement...

    Here is a link to ADA racing for replacement domes. https://adaracing.com/personal-watercraft-products/pwc-domes/dome-kawasaki-ultra-150-1200-stxr-billet-head/
  9. Replies
    29
    Views
    1,420

    I see you have one of the heads off. Post a pic...

    I see you have one of the heads off. Post a pic of the chamber on like a 45 deg angle I can probably tell you if they are 42 or 36
  10. Replies
    29
    Views
    1,420

    I have a set of skiworx billet heads with...

    I have a set of skiworx billet heads with interchangeable domes for sale. PM me if interested.
  11. Replies
    29
    Views
    1,420

    As you said the6 come in 42cc or 36cc. With stock...

    As you said the6 come in 42cc or 36cc. With stock pistons 42cc should around 145psi and 36cc should be around 180psi. Now groupk also modified these heads to use on their level 2 kits with modified...
  12. Replies
    1
    Views
    242

    You should post this up on PWCtoday in the...

    You should post this up on PWCtoday in the general section. Someone over there may know. http://www.pwctoday.com/forumdisplay.php?f=11
  13. Reverse bucket ? Maybe try to find someone with...

    Reverse bucket ? Maybe try to find someone with a 300 in your area so you can swap complete pump and test.
  14. Thread: 2012 stx15f

    by TMiller
    Replies
    7
    Views
    465

    See if this helps ...

    See if this helps http://greenhulk.net/forums/showthread.php?t=282377
  15. Replies
    9
    Views
    712

    180 psi must have been a typo. The original post...

    180 psi must have been a typo. The original post says the other 2 cylinders are at 130 and looks like a stock head in the background.
  16. Replies
    9
    Views
    712

    Whoops.....

    Whoops.....
  17. Replies
    9
    Views
    712

    Ring probably moved once the pin was gone. ...

    Ring probably moved once the pin was gone.

    May be fuel system related. How old is the fuel? You could put the heads back on and pressure test the motor to rule out air an air leak.
  18. Replies
    2
    Views
    309

    You can look in the greenhulk parts store on the...

    You can look in the greenhulk parts store on the diagram.
  19. Replies
    10
    Views
    631

    I was going to offer you a intake manifold but I...

    I was going to offer you a intake manifold but I see you are in UK so probably cheaper to pay someone to remove the bolt. If you want to try it yourself- REMOVE MANIFOLD FROM MOTOR, center punch the...
  20. Replies
    5
    Views
    452

    WTB - Parts Are you looking for oem pump or Skat Trac ?

    Are you looking for oem pump or Skat Trac ?
  21. WTB - Parts PM sent

    PM sent
  22. Replies
    10
    Views
    549

    Oh the ford 2.3 pony stock motor. That would be...

    Oh the ford 2.3 pony stock motor. That would be cheap to build an iron block one but if the weight is a concern then might not work for you. There was a version of that motor that used a stroked...
  23. Replies
    10
    Views
    549

    What kind of numbers are they getting out of the...

    What kind of numbers are they getting out of the ford 2.3? You mean the newer 4 valve head yea? That seems like it would be hard to beat with a turbo on it.
  24. Replies
    76
    Views
    6,333

    Hey this is fun ! I could do this all day ! ...

    Hey this is fun ! I could do this all day ! :beatdeadhorse5:
  25. Have you pulled the fuel pickup out and inspected...

    Have you pulled the fuel pickup out and inspected it? I had one with a cracked tube, they are old and brittle.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4