Search

Type: Posts; User: boudin

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    28
    Views
    938

    I have only the older version myself, so do not...

    I have only the older version myself, so do not know.
  2. Replies
    28
    Views
    938

    The gauge cluster rolls over at 1000. Below is a...

    The gauge cluster rolls over at 1000. Below is a pic of YDS on a high hour ski.
  3. Replies
    6
    Views
    224

    When you say "5 hours on SBT rebuild" do you mean...

    When you say "5 hours on SBT rebuild" do you mean you have 5 hours on a motor shipped from SBT, or a broken older SBT motor that you rebuilt and have 5 hours on?

    If the former, unfortunately you...
  4. Replies
    4
    Views
    312

    Timing chain sprocket looks good, but the cams...

    Timing chain sprocket looks good, but the cams are not. Line-up the outermost markers, like the red line in @blakegjones pic.

    Tips:

    Try to get the chain on the opposite side of the tensioner...
  5. Here you go.

    Here you go.
  6. Replies
    28
    Views
    938

    Or a 32-bit integer by now. -Greg

    Or a 32-bit integer by now.

    -Greg
  7. The two nipples on the generator housing cover...

    The two nipples on the generator housing cover are also susceptible to this. Had one break the other day when I was removing a hose. Unfortunately unrepairable as they are cast into the cover.
    ...
  8. Replies
    4
    Views
    205

    What's the history of the ski? Has it been...

    What's the history of the ski? Has it been sitting for a long time and you are now trying to fire it up, or did this condition just start?

    If you removed the fuel rail and injectors and are not...
  9. Replies
    28
    Views
    938

    The total hours are calculated as a 16-bit...

    The total hours are calculated as a 16-bit unsigned integer, which is why it reads 655.36 max. Manually add up the RPM range hours to get the actual total hours.

    -Greg
  10. Replies
    13
    Views
    256

    Yep, rod caps do have an orientation on the rod....

    Yep, rod caps do have an orientation on the rod. From your original description I thought you were talking about the entire rod on the big end.

    Also, make sure you are using all the same weight...
  11. Before doing the compression test, from the front...

    Before doing the compression test, from the front of the ski, reach in and pull out the electrical plug from the fuel pump. A pair of needle nose might be needed to squeeze the connector and pull it...
  12. Replies
    13
    Views
    256

    Correct. -Greg

    Correct.

    -Greg
  13. Replies
    13
    Views
    256

    Looking through the shop manual again, I don't...

    Looking through the shop manual again, I don't see where the orientation of the con rods matters, but I do myself make sure the weight stamp is oriented all the same direction. I do always...
  14. Replies
    3
    Views
    105

    SOLD Thanks. Picked up one local from 1_Fast_SHO just...

    Thanks. Picked up one local from 1_Fast_SHO just now. Thanks, guys!
  15. Replies
    3
    Views
    105

    SOLD WTB: GP1300R Fuel Tank

    Looking for a GP1300R fuel tank. Please PM me price shipped to 75862. Thanks.

    -Greg
  16. Replies
    6
    Views
    232

    Partially lower your reverse gate to slow you...

    Partially lower your reverse gate to slow you down at idle.
  17. Reserve has a longer pickup tube that reaches...

    Reserve has a longer pickup tube that reaches deeper into the tank.
  18. Replies
    4
    Views
    220

    If you ever open the seat to find the hull full...

    If you ever open the seat to find the hull full of water, open the drain holes in the back of the ski then run like hull. The water will drain pretty quickly out the drain holds. Pretty...
  19. Replies
    4
    Views
    220

    It should be pretty water tight. Not only the...

    It should be pretty water tight. Not only the rubber plugs around the wires, but there is an o-ring that seals the mating surface.

    This has happened to me on more than one 12F/15F; the stock...
  20. Replies
    19
    Views
    628

    It's not that uncommon the 12F/15Fs to hear a...

    It's not that uncommon the 12F/15Fs to hear a tick. I would not worry about it, but at some point you should probably do a valve adjustment. Not all that hard, but a little trickier with the motor in...
  21. Replies
    5
    Views
    181

    Do you have YDS to check which code? (Can't...

    Do you have YDS to check which code? (Can't remember how to get the code on the dash--spoiled by YDS.)

    I've seen this before when the intake cooling line (under PTO area) had a kink and would not...
  22. Replies
    3
    Views
    233

    Would be good to list your location.

    Would be good to list your location.
  23. Replies
    2
    Views
    207

    What service work was done with the motor out?...

    What service work was done with the motor out? What color are the plugs?

    I would also send the injectors out to be cleaned and spray tested. A leaky injector could also cause the fuel pressure to...
  24. Replies
    4
    Views
    370

    I highly recommend these folks for injector...

    I highly recommend these folks for injector service. Costs me about $100 including shipping both ways for four injectors. Cheap price to pay to know you are at peak injector performance.
    ...
  25. So you have two problems? (1) Water leak; (2) ski...

    So you have two problems? (1) Water leak; (2) ski will no longer start?

    (1) As others have pointed out, the pipe joint is notorious for leaking on the pre-2010 VXs. Yamaha did not use enough glue...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4