Search

Type: Posts; User: infernojoe

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    273

    Same kit will fit 1100 or 760.

    Same kit will fit 1100 or 760.
  2. Replies
    4
    Views
    281

    Absolutely! Seadoo has the same issue on older...

    Absolutely! Seadoo has the same issue on older pipes on the lower freeze plug welded caps. $5 water weld putty will fix it for a couple of years vs pulling the pipe and finding a good welder.
  3. Well this won't help but I had to work on one a...

    Well this won't help but I had to work on one a few years ago and the only thing that fixed it was a new Computer module. Both matching units and then it was sold. i got lucky and found it cheap. My...
  4. Replies
    1
    Views
    200

    Oil Fuel and temp. At the same time.. has to be...

    Oil Fuel and temp. At the same time.. has to be a connection or the cluster just flaked out.. As long as your engine temp is good i wouldn't worry about it.
    None of my older ones have working...
  5. Replies
    8
    Views
    273

    Yes they will get crud on the connectors. they...

    Yes they will get crud on the connectors. they can be cleaned but its tricky. Tiny springs and contacts in there. As for grease.. go light. not often.. rear PTO bearing just a few squirts.. starter...
  6. Replies
    4
    Views
    240

    some type of water screen. never have i found...

    some type of water screen. never have i found one in a 1200r.. odd.
  7. pull the jugs. pull the rings. run a light hone...

    pull the jugs. pull the rings. run a light hone through it and inspect for any spots or out of round. any nicks in the ports.. get some wave eaters for the powervalves. you should have 120ish on both...
  8. Yes!! Yamaha's love new plug.

    Yes!! Yamaha's love new plug.
  9. Replies
    11
    Views
    438

    Key fob. security? I have had them do that when...

    Key fob. security? I have had them do that when locked. Fast presses will try to turn but won't.
  10. Also check comp on another gauge.. wide open ...

    Also check comp on another gauge.. wide open with plugs in the other holes.. no wires of course.. that thing should be a solid 120 psi in good shape. The entire burn and power will never be right if...
  11. Looks good to me.. center cyl is a little lighter...

    Looks good to me.. center cyl is a little lighter but not bad. Pistons and cyl. walls have some wear but if you are not ready to freshen it up just copper coat the shit out of the new head gasket....
  12. Replies
    1
    Views
    152

    Try another servo motor.. it should cycle after...

    Try another servo motor.. it should cycle after shut down. even then I have seen some erratic movement from them when they act up.
  13. Replies
    3
    Views
    187

    You can get the stock jetting on the riva site. ...

    You can get the stock jetting on the riva site. Just a bore and port may not require a jet change.. unless you get past the mix screw range.. If you are doing a spec. setup such as a Group K....
  14. Replies
    1
    Views
    115

    I just did one a few months ago. it is tight but...

    I just did one a few months ago. it is tight but it will flex to the front enough to clear.
    you can empty the tank and unbolt the straps to lean it forward but it can be done without it.
  15. Those are the best motors... Blaster 1 and 2 guys...

    Those are the best motors... Blaster 1 and 2 guys love those for conversions..
    If you want it to be right. get a compression check done. do the carbs.. do the oil block off and go premix.. if you...
  16. Replies
    8
    Views
    378

    The only time I saw the injector sticking at my...

    The only time I saw the injector sticking at my shop was when the elect. box had water in it and faulted the ECU. . At least 5 I can remember and all had a water line 2 inches high.
Results 1 to 16 of 16