Search

Page 1 of 16 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    9
    Views
    664

    4-Stroke Thanks to Chris from Lacey powersports and his...

    Thanks to Chris from Lacey powersports and his son the motor is almost ready to go in!
    ...
  2. Replies
    300
    Views
    40,432

    Thanks man! I'm loving it...

    Thanks man! I'm loving it...
  3. Replies
    169
    Views
    20,055

    4-Stroke I am going to measure it this week. Its easy to...

    I am going to measure it this week. Its easy to measure. Just measure the lobe to base and base circle by itself. Lift is the difference.

    Robert
  4. Replies
    79
    Views
    12,575

    Pulled the pump on my '18 gp and measured the...

    Pulled the pump on my '18 gp and measured the back side of the pump. 6.3" which is 160mm. Compared the outlet of the pump to the nozzle on my '18 Vxr. Identical. So the 6 vane, 8 vane and the new...
  5. Replies
    169
    Views
    20,055

    4-Stroke Head is ready to be picked up. We are going to...

    Head is ready to be picked up. We are going to check spring pressures and probably adjust. I need to get the lift from the RC-3 cams vs stock SVHO cams. He made lots of small improvements in the...
  6. Replies
    79
    Views
    12,575

    Nah man, at worst he got some bad info forwarded...

    Nah man, at worst he got some bad info forwarded to him. He's a middle man and never steered anyone wrong for the last 14yrs or so. Hell even told me many o times to not buy parts bc they wouldn't...
  7. Replies
    6
    Views
    342

    Well, here's the thing—I don't necessarily need...

    Well, here's the thing—I don't necessarily need to get this boat on the water because I have a few SHO's and a SVHO all in perfect condition. However if I could get this ski back on the water without...
  8. Replies
    169
    Views
    20,055

    4-Stroke Here are the clearances: rod oil clearance...

    Here are the clearances:

    rod oil clearance .002
    main oil clearance .001
    rod side clearance .006
    crankshaft end clearance .005

    The rod clearance was .003 (excessive) as received from other...
  9. Replies
    35
    Views
    2,624

    Is this a question or statement? You stated...

    Is this a question or statement? You stated earlier that the clutch has only 1 hr on it?
  10. Replies
    126
    Views
    6,057

    The pipe is louder, guaranteed

    The pipe is louder, guaranteed
  11. Replies
    35
    Views
    2,624

    If you have water coming out of all the pissers...

    If you have water coming out of all the pissers and aren’t getting an overheat warning then sand in the cooling is not your issue
  12. Replies
    35
    Views
    2,624

    I agree. Sand isn't the issue.

    I agree. Sand isn't the issue.
  13. Replies
    126
    Views
    6,057

    i think ill get the fizzle water box delete...

    i think ill get the fizzle water box delete through hull for my ski after reading this post just to piss some tree huggers off...thats all folks
  14. Replies
    126
    Views
    6,057

    Ride a bike across the 401, one with stock...

    Ride a bike across the 401, one with stock exhaust and one with straights. Alot less accidental lane change by cars on the bike with the pipes......just sayin'......
  15. Replies
    11
    Views
    751

    Splitting hairs but the stock retainers should be...

    Splitting hairs but the stock retainers should be good for 8650 rpms I thought.
  16. Replies
    29
    Views
    1,155

    Ha.....actually I set a 1/4' drive ratchet...

    Ha.....actually I set a 1/4' drive ratchet extension in the hole and put the tip of the dial indicator down in the end of the extension. good enough to watch the dial move!!
  17. Replies
    169
    Views
    20,055

    4-Stroke I am not sure what he is looking for, but I can...

    I am not sure what he is looking for, but I can find out what it ends up at.

    Robert
  18. Replies
    29
    Views
    1,155

    Make sure you have fire, fuel and compression, if...

    Make sure you have fire, fuel and compression, if all are good its most likely a timing issue.
  19. FS Like New ET Billet Supercharger 24lb and aditional New never used 28lb Wheel

    Like New ET Billet Supercharger 24lb and additional New never used 28lb Wheel $2,500
  20. Replies
    16
    Views
    1,201

    Never experienced this in thirty years of...

    Never experienced this in thirty years of building engines, maybe I change plugs too often? Here's pic of the side gapping. The plug on the left is before, on the right after. Another tip is...
  21. Replies
    16
    Views
    1,201

    I’m running the gap at 16 thousands. 30 LBS...

    I’m running the gap at 16 thousands.

    30 LBS Boost @ 9850 rpms on E85...
  22. Replies
    8
    Views
    632

    I can't compare the Riva I/C to the Fizzle models...

    I can't compare the Riva I/C to the Fizzle models because I've never owned a Riva unit...but I can tell you that my Fizzle Y1000 and 500 intercoolers have been awesome and one of the best purchases...
  23. Replies
    66
    Views
    3,802

    with the riva map tune stage 3, 17 lb wheel. 9500...

    with the riva map tune stage 3, 17 lb wheel. 9500 tune...stock fuel pump, 88 mph @ 9200 arf 11.9-12.1 spring and fall. summer 87.7 mph @ 9140r's, arf a little richer ,40 hrs on build no problems.
  24. FS - Parts SVHO HKS Supercharger with R&D shaft and 17lb wheel

    Off my 2017 FX. Has been pinned and will make 21lbs. of boost at 9000 rpm's. $1100 shipped within U.S.
  25. Here's the issue that CR has seen with clutches...

    Here's the issue that CR has seen with clutches that have failed.....

    People didn't follow instructions, or were not provided with proper instructions when the clutch was sold to them. The...
Results 1 to 25 of 400
Page 1 of 16 1 2 3 4