Search

Type: Posts; User: m4f1050

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    20
    Views
    1,224

    Thanks. I will start searching as well.

    Thanks. I will start searching as well.
  2. Replies
    20
    Views
    1,224

    Awesome, thanks!

    Awesome, thanks!
  3. Replies
    20
    Views
    1,224

    This is exactly what I posted but I got no...

    This is exactly what I posted but I got no reply...
  4. Replies
    20
    Views
    1,224

    Is that the connector cover? Or is there a cover...

    Is that the connector cover? Or is there a cover on top of that connector?

    http://partsfinder.onlinemicrofiche.com/4tec/showmodel.asp?type=13&make=yamahapwc&a=295

    Electrical 1, item #31
    ...
  5. Replies
    20
    Views
    1,224

    Haven't found it yet. I hope I don't have to buy...

    Haven't found it yet. I hope I don't have to buy a harness just for this plug...
  6. Replies
    20
    Views
    1,224

    Still looking for this plug. Anybody with a...

    Still looking for this plug. Anybody with a GP1800 2018+ can check?
  7. Replies
    8
    Views
    553

    Diagnostic cable and YDS is no good for 2014 and...

    Diagnostic cable and YDS is no good for 2014 and newer waverunners, so anybody doing similar project can get a 4-pin plug male/females for the project.
    Still looking for the newer 44-pin plug on...
  8. Thread: YDS Software

    by m4f1050
    Replies
    4
    Views
    952

    Tested it, but it's only good for 2013 and older...

    Tested it, but it's only good for 2013 and older waverunners. It's better to get CanDoo for this.
  9. Replies
    8
    Views
    553

    Bench harness for diagnostic and reflashing....

    Bench harness for diagnostic and reflashing.
    Have I answered your question(s)? What was your desire to know the answer to the question(s)?



    That's too much money. I paid $40 for everything...
  10. Replies
    8
    Views
    553

    Updated list Left side SUPERSEAL 1.0mm,...

    Updated list

    Left side
    SUPERSEAL 1.0mm, Housing for female terminals, Wire-to-Board / Wire-to-Device, 26 Position, 3mm [.118in] Centerline, Sealable, Black...
  11. Replies
    20
    Views
    1,224

    Yeah, checked TE, nothing. For SHO/SVHO up to...

    Yeah, checked TE, nothing.

    For SHO/SVHO up to 2017 I can get them at TE, Corsa-technic, Newark/element14, but none of these sites have this 44-pin (2018 and up) plug.
  12. Replies
    20
    Views
    1,224

    Nothing? Do they sell them like they sell...

    Nothing? Do they sell them like they sell Sea-Doo ECU plugs to repair them?
  13. Replies
    20
    Views
    1,224

    2018+ (2017 is the same as SVHO) Should be 44...

    2018+ (2017 is the same as SVHO) Should be 44 position.
  14. Replies
    20
    Views
    1,224

    ECU plugs Yamaha GP1800

    Does anybody know which plugs are used for Yamaha GP1800 ECU? I found the ones for FZR/FZS but I couldn't find anything for the GP1800 on TE website.

    Thanks.
  15. Replies
    8
    Views
    553

    Here is some info I've gathered on the net.

    Here is some info I've gathered on the net.
  16. Replies
    8
    Views
    553

    I guess nobody is interested in this... Left...

    I guess nobody is interested in this...

    Left
    https://www.te.com/usa-en/product-3-1437290-8.html?source=header-match

    Middle...
  17. Replies
    8
    Views
    553

    ECU plugs Yamaha FZR/FZS

    Does anybody know which plugs are used for Yamaha FZR/FZS?

    https://www.te.com/usa-en/product-CAT-SU763-CH8172.html

    I'm mainly looking for the center/middle one. But if you can identify and...
  18. Replies
    1
    Views
    368

    1630 ACE top speed?

    Is the international (RS) 1630 ACE powered machine still have a higher top speed? Is it limited and does it also need a SCOM?
    Will changing the ECM's Country/Market from C/U to INT, Europe or "Not...
  19. Replies
    26
    Views
    2,535

    Im not going to pitch too low, but I'm sure it...

    Im not going to pitch too low, but I'm sure it will rev past 9.5k RPM and I want to be on the safe side. If it can be safe revving 10k it will give me some piece of mind. I believe overdoing it on...
  20. Replies
    26
    Views
    2,535

    I'm using a ViPEC.

    I'm using a ViPEC.
  21. Replies
    26
    Views
    2,535

    Lower pitch for quicker holeshot. Target is not...

    Lower pitch for quicker holeshot. Target is not the psi.
  22. Replies
    26
    Views
    2,535

    Wait a minute, I can't use re-sleeving if I want...

    Wait a minute, I can't use re-sleeving if I want to go past Stage II? I want to build E85, 23#, revin' past 9.5k...
  23. Replies
    26
    Views
    2,535

    It adds up. You are correct, it is (or was) a...

    It adds up. You are correct, it is (or was) a Stage IV (23#) and yes, it was honed. I am guessing it was a bit worn out. But regardless I would not use regular piston rings on plasma. I guess I...
  24. Replies
    26
    Views
    2,535

    Ok thanks.

    Ok thanks.
  25. Replies
    26
    Views
    2,535

    Refreshing motor (new bearings and rings) Any...

    Refreshing motor (new bearings and rings)
    Any links for iron sleeving job?
Results 1 to 25 of 88
Page 1 of 4 1 2 3 4