Search

Page 1 of 2 1 2

Search: Search took 1.00 seconds.

  1. Sticky: New attempt to keep it 100% stock until warranty...

    New attempt to keep it 100% stock until warranty expires!?
  2. Replies
    8
    Views
    345

    rxpx300 intermediate cooler mounting

    People tried and got high temp oil alarms.

    The oil cooler for the 260 was not sufficient for the 300 block.
    But there was no space in the hull to install a larger oil cooler on the 300 engine.
    ...
  3. The hat will not pass through the tru-hull...

    The hat will not pass through the tru-hull opening.
    Cut the bellow and break the carbon ring.
    Then tap/hammer the hat towards the aft to expose and remove C-clip.
    Then the hat has to come off...
  4. Replies
    2
    Views
    654

    View Post

    I think itís pretty good described.
    One is a diagnostic tool and the other a tuning/flashing tool.

    ...
  5. Replies
    35
    Views
    1,282

    Check your IC also again. Those rpm numbers are...

    Check your IC also again.
    Those rpm numbers are exactly the ones Iíve experienced with leak ones.
    Your wear ring / prop should be ok as your missing rpmís and speed, not only speed.
  6. Replies
    6
    Views
    1,898

    The 2 brackets on the hull should be aligned...

    The 2 brackets on the hull should be aligned better. I have mine installed myself and remember to have them close as possible. That the rack fits between when holding the red lock.
    I never lost it...
  7. If you use the black 3/4 outlets from GH store...

    If you use the black 3/4 outlets from GH store you can just push the garden hose in there.

    Clamp of the small 3/8 hose from exhaust manifold to waterbox and you can do it with engine stopped.
  8. Thread: IBR fault code

    by EVN81
    Replies
    11
    Views
    900

    Serious does anybody read the owners...

    Serious does anybody read the owners manual.........?

    Page 111 (for RXP)
  9. Well.... NOT on NGK plugs! ...

    Well.... NOT on NGK plugs!

    http://b2600i.com/images/ngk_tb_0630111_antisieze.pdf

    http://greenhulk.net/forums/attachment.php?attachmentid=448847&stc=1
  10. Replies
    9
    Views
    578

    What hoses should go here?!?!

    No itís not. The hose you see is the incoming cooling line from jetpump. It passes through a cap on the iBr actuator where the temp. sensor sits and from there it splits in 2 to IC and exhaust...
  11. Replies
    9
    Views
    578

    What hoses should go here?!?!

    There you should be your bailer hoses connected.
    For sure youíll taking in water.
    And one connection is even broken.
    You need to replace that part.

    Or (this is not very good advice) block the...
  12. Replies
    8
    Views
    430

    Yes

    Yes
  13. Replies
    10
    Views
    544

    2010 rxt-x ibr brackets

    From 2013 and up they were updated if Iím correct. Compare the P/N in the partsfinder catalogue.

    But you have the rideplate mounted pump with cooling water supply next to / under the iBr motor. So...
  14. :facepalm: 1 or 2 minutes without hose...

    :facepalm: 1 or 2 minutes without hose connected.....
    You ever studied exhaust system. It has al kinda rubber hoses and a plastic resonator.

    Check on display which faultcode you have
  15. Thanks for the info [emoji106] Think I have to...

    Thanks for the info [emoji106]
    Think I have to send in a dash soon (17 TX)
  16. You verified voltage and condition of battery? ...

    You verified voltage and condition of battery?

    Never jumpstart a ski with cables from different battery! Risk of frying ECU.
    Charge or replace original battery.
  17. Maybe it's 1/8" BSP (parallel, not tapered) ?

    Maybe it's 1/8" BSP (parallel, not tapered) ?
  18. Thread: SCOM for a 230?

    by EVN81
    Replies
    59
    Views
    7,054

    Was reading the 2018 workshop manual today (thank...

    Was reading the 2018 workshop manual today (thank you member Scott for sharing!)

    And BRP significantly raised the max RPM limits compared to the 'old' 260 engines
    ...
  19. Replies
    14
    Views
    2,358

    Cut / break / saw out plastic piece behind iBR...

    Cut / break / saw out plastic piece behind iBR actuator.
    Until you can get a hold with long nose pliers at plastic pieces with brass nut.

    Good luck............
  20. Replies
    16
    Views
    3,986

    Heads up 2 Here you find the correct one: ...

    Heads up 2

    Here you find the correct one:

    http://www.greenhulk.net/forums/showthread.php?t=257204&page=2
  21. Thread: 2018 line up

    by EVN81
    Replies
    222
    Views
    45,904

    And after everybody can start crying and...

    And after everybody can start crying and complaining again how disappointed they are.........
  22. Replies
    10
    Views
    2,568

    You forgot 1 important step...... Have some...

    You forgot 1 important step......

    Have some beers ready as well :cool:

    http://www.greenhulk.net/forums/attachment.php?attachmentid=421027&stc=1
  23. Only 132mm difference........ I stick to my...

    Only 132mm difference........

    I stick to my 1/4" - 3/8" rule of thumb
  24. Replies
    5
    Views
    826

    Fault code would be helpful :-k

    Fault code would be helpful :-k
  25. Well you have the TSB now, which clearly stated:...

    Well you have the TSB now, which clearly stated:

    Hexagon bolts M8x30
    Use thread locker
    Torque twice 35 nM
    Wait 1 day to dry

    Cannot see how your dealer can ignore that.......
Results 1 to 25 of 50
Page 1 of 2 1 2