Search

Type: Posts; User: Hazard Racing

Search: Search took 0.00 seconds.

  1. Replies
    19
    Views
    1,060

    K447 Thank you for your in put on your hull...

    K447

    Thank you for your in put on your hull design thoughts.

    Still looking for the magic to make it lift.
  2. Replies
    11
    Views
    891

    To answer your question. Yes the 6 vane SS...

    To answer your question.
    Yes the 6 vane SS stator will work on that boat.
    There are plenty of extended ride plates on EBAY for that boat as well as the 6 vane stator.
    Drive shafts on Ebay as well....
  3. Replies
    12
    Views
    1,393

    Savage Man Thanks for the reply. You seam...

    Savage Man

    Thanks for the reply.

    You seam to be very lucky finding all the old Hot Seat parts, i have not had much luck here in Michigan.

    Where do you ride at ? Looks like a large lake in...
  4. Replies
    19
    Views
    1,060

    As you can see the pump is in a fairly straight...

    As you can see the pump is in a fairly straight plane with the bottom of the hull.

    http://greenhulk.net/forums/attachment.php?attachmentid=454351&stc=1
  5. Replies
    19
    Views
    1,060

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=454264&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=454265&stc=1
  6. Replies
    19
    Views
    1,060

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=454263&stc=1
  7. Replies
    19
    Views
    1,060

    The ported cylinders and cut heads are not done...

    The ported cylinders and cut heads are not done yet, so we can't say on the squish and compression.
    He is told that the pipes should run at 8,000 rpm.

    The stock port timing is probably holding...
  8. Replies
    11
    Views
    1,220

    Thank you pro1200 and Bruce for the reply’s . ...

    Thank you pro1200 and Bruce for the reply’s .

    Randy

    would like to find one of these Watcon or Hot Seat tide plates.
    I am a sheet metal fabricator by trade, I could make my own if I had one to...
  9. Replies
    11
    Views
    1,220

    pro1200 When you ran the AAT did you bore the...

    pro1200

    When you ran the AAT did you bore the nozzle to 87mm like Bruce suggests ?

    I also have a 1200 Pro and was looking at getting one of these, in an effort to gain more top speed.
    Bruce...
  10. Replies
    12
    Views
    1,393

    How is your 1200 Polaris project coming along? ...

    How is your 1200 Polaris project coming along?

    A friend on mine has a similar 1050 hull with an 1165cc motor , stock single pipe,
    Hot seat water box, Hot seat CDI ,92 domes , D Flan port job,...
  11. Replies
    19
    Views
    1,060

    The stock TX 1200 drive shaft. That’s why we...

    The stock TX 1200 drive shaft.

    That’s why we are looking for info to get ahold of Ted and get some hardened ones made.

    Any leads on hardened shafts?
  12. Replies
    19
    Views
    1,060

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=453963&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=453964&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=453965&s...
  13. Replies
    19
    Views
    1,060

    Polaris TX 1200 Hydro

    This is my buddy Matt's boat.
    This was four year project, with more to go before its ready for paint.

    The base is 1979 HydroStream 15' , with the engine and pump neatly trimmed out of the bottom...
  14. Replies
    5
    Views
    869

    Posts Renjon V-force reeds, or Boyesen Pro...

    Posts

    Renjon

    V-force reeds, or Boyesen Pro peddles.
    Reed angle spacers from a 785 Pro might work.
    Used Pro 785 intake and used Pro 785 44mm carbs ( eBay $100)
    Only use non- ethanol 90octane...
  15. Replies
    1
    Views
    419

    Dude V-force reeds, or Boyesen Pro peddles....

    Dude

    V-force reeds, or Boyesen Pro peddles.
    Reed angle spacers from a 785 Pro might work.
    Used Pro 785 intake and used Pro 785 44mm carbs ( eBay $100)
    Only use non- ethanol 90octane fuel or...
Results 1 to 15 of 15