Search

Page 1 of 5 1 2 3 4

Search: Search took 1.00 seconds.

  1. A lot of FZ & Gp been doing 90 with retainers.....

    A lot of FZ & Gp been doing 90 with retainers.. all in the rpm's. With stock wheel.
  2. Replies
    45
    Views
    4,524

    again, we are arguing over not doing something...

    again, we are arguing over not doing something that takes 5 min and is free. blow water out of your ski or don't. its not a bad idea... sure may not be needed. but it aslo does not hurt.....
  3. I too drop nose and jack trailer on left side to...

    I too drop nose and jack trailer on left side to lower dipstick side. I do so AFTER sucking it out level and I do get more out. probably 1/2 a quart.
  4. Replies
    45
    Views
    4,524

    TXDroneRacer how do you have a avitar that...

    TXDroneRacer

    how do you have a avitar that swaps?
  5. Again that's not correct. Yes spinning the motor...

    Again that's not correct. Yes spinning the motor higher in the RPM does make more boost and power..... that being said a 13/18 allows the motor to spin the higher RPM on lower powred machines. but...
  6. All that is correct but saying the lower the...

    All that is correct but saying the lower the pitch the faster is nor correct. it can be faster, but if you have the power to spin the bigger prop to same RPM its not faster.
  7. I don't have a GP, but on my FZ the plat is...

    I don't have a GP, but on my FZ the plat is resessed up into the hull like your picture shows. I though it was weird too but all 3 of my plates have done that. and the cut one go far up in there and...
  8. Replies
    3
    Views
    266

    Solas solid Stainless wear ring is what I replace...

    Solas solid Stainless wear ring is what I replace them with. bolts on like stock, no more swelling.
  9. Nothing. Stock grate Middle bar cut out, Stock...

    Nothing. Stock grate Middle bar cut out, Stock plate cut with 1 washer in front (paddle wheel block off palte), no sealant, 2 degree wedge and stock nozzle.
  10. Replies
    3
    Views
    530

    I think the issues where with Sola and a prop...

    I think the issues where with Sola and a prop made for seadoos. and they changed the blade thickness.
  11. Replies
    23
    Views
    2,107

    There is a thing as too mich cooling. then you...

    There is a thing as too mich cooling. then you can get Gas in oil and that's not good.
  12. Thread: Intro!

    by mittens
    Replies
    5
    Views
    257

    Welcome tons of info, and helpfulness. Search...

    Welcome tons of info, and helpfulness. Search function helps sort it. also remember when searching if you need a whole frase to be the search use ""

    for example searching EX prop you will get...
  13. Bouncing the limiter is one thing. the clutch...

    Bouncing the limiter is one thing. the clutch free wheels all the time the wearing items are the on/off/on/off when under power, and high RPMS.. I know people say its horrible for them but to rev...
  14. Replies
    30
    Views
    4,281

    FOr what its worth, I use a 3/8 rachet around the...

    FOr what its worth, I use a 3/8 rachet around the oil pump first and then go back and Torque to spec and they are always over tightened by hand just using one hand and a normal rachet. the oil pump...
  15. Thread: Turbo FZ Build

    by mittens
    Replies
    78
    Views
    6,158

    4-Stroke So swapped my ride plate out & now with the wedge...

    So swapped my ride plate out & now with the wedge & other plate that has more trim cut into it... ski now carrys the bow. 91mph 9350 rpms. & I learned I am
    not at 17lbs. I have been watching air...
  16. Replies
    2
    Views
    377

    Or it could have a knock. and sensor is good. ...

    Or it could have a knock. and sensor is good.

    Probably not but pay attention. mechanic stethoscope... is helpful lessoning to things. also can make you paranoid ha.
  17. Replies
    10
    Views
    882

    The stock SVHO wheel can do that boost level if...

    The stock SVHO wheel can do that boost level if you spin it more. being gear driven and no trans speed on a ski is all about RPM. Stock SVHO wheel at 8800 rpms is 16.4 lbs.

    You will still need...
  18. Thread: Turbo FZ Build

    by mittens
    Replies
    78
    Views
    6,158

    4-Stroke After a few rides (4), whole systems seems to be...

    After a few rides (4), whole systems seems to be working good. I had a V Band leak between the Turbine and the Up pipe.... which disappointed me as that's the point of V bands!. I guess there is a...
  19. Yea Crank bolt is re usable. So is o-ring on...

    Yea Crank bolt is re usable.

    So is o-ring on Super charger.

    And the Crush washer/ rubber coated washers (4), I have re used as well. more then once.
  20. Thread: MB 2021 Dates

    by mittens
    Replies
    35
    Views
    4,816

    Roger that. So travel Thursday 10th, Ride 11,...

    Roger that. So travel Thursday 10th, Ride 11, and 12th, Go home 13th.
  21. Thread: Turbo FZ Build

    by mittens
    Replies
    78
    Views
    6,158

    4-Stroke Thanks! my worry with a brace is I wanted...

    Thanks!

    my worry with a brace is I wanted (think it needs) to all move with the motor. So can't just brace it on the hull in the rear. Open to suggestions but seems like everyone just floats them...
  22. Thread: Turbo FZ Build

    by mittens
    Replies
    78
    Views
    6,158

    4-Stroke The Turbo used was a Borg Warner EFR 6758. ...

    The Turbo used was a Borg Warner EFR 6758. Turbine housing is a 0.85 AR housing made of Case Stainless Steal. Welded the 304 SS jacket around it. Few pics of it. Water bung on the top and bottom...
  23. Thread: Turbo FZ Build

    by mittens
    Replies
    78
    Views
    6,158

    4-Stroke Turbo FZ Build

    Wanted to start a build thread with all the pics and info I can provide in one place. I try and keep good records, maybe this will be helpful to others.

    My Goal was a bolt on Turbo set up that...
  24. Replies
    158
    Views
    90,495

    With the price of wood right now, that probably...

    With the price of wood right now, that probably cost more then buying a fancy one! haha nice work though
  25. Here are a few showing how it mounts in ski. Test...

    Here are a few showing how it mounts in ski. Test fitting it. I wanted the down pipe to come up high & drop back so all water being injected back would drain out the exhaust & hopefully means the 02...
Results 1 to 25 of 117
Page 1 of 5 1 2 3 4