Search

Page 1 of 9 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    35
    Views
    6,603

    The 215/255 OEM head gaskets are not prone to...

    The 215/255 OEM head gaskets are not prone to failure. Its not going to hurt to use a 300 gasket, but if you have other problems, the 300 gasket is not going fix it.
  2. Replies
    8
    Views
    197

    I would not mod an SBT engine. you're rolling the...

    I would not mod an SBT engine. you're rolling the dice with running it stock.
  3. Replies
    14
    Views
    692

    First you stated that he said it was just...

    First you stated that he said it was just rebuilt. That's obviously not the case. Seller misrepresented the item. Members need to know who the seller is so they can be " Careful what you buy" and...
  4. Replies
    6
    Views
    283

    I would go with the proven supertech valves. I...

    I would go with the proven supertech valves. I would not put cheap aftermarket valves in any of my skis, stock or modified.
  5. Sticky: What will they think of next, a maintenance kit...

    What will they think of next, a maintenance kit for maintenance free supercharger...
  6. Thread: 98 GS pump seal?

    by ncdoo
    Replies
    9
    Views
    413

    With silcone sealant, they're a PITA to get back...

    With silcone sealant, they're a PITA to get back off. I would go with rubber seal shpown on the other models.
  7. Replies
    2
    Views
    144

    No worries as long as water didn't get in the...

    No worries as long as water didn't get in the engine. I would check both electrical boxes for water. Make sure they're dry on the inside. Put it in the water and check for leaks. If none, you should...
  8. Thread: Water pump issue

    by ncdoo
    Replies
    29
    Views
    1,674

    If you're interested, PM me your email and I'll...

    If you're interested, PM me your email and I'll send you an electronic copy. I dont have one for your specific year but most of the engine information is the same from year to year.
  9. Replies
    28
    Views
    1,916

    He could have bought the head of eBay, he never...

    He could have bought the head of eBay, he never mentioned a name. IMO it should have been put in a plastic bag prior to taking it to be packed. Good look cleaning that mess up.
  10. Thread: ARP Head studs

    by ncdoo
    Replies
    4
    Views
    269

    SOLD I have some good used rod bolts and rocker arm...

    I have some good used rod bolts and rocker arm bolts, cheap... :)
  11. Replies
    30
    Views
    1,195

    You'll need to check the number located on the...

    You'll need to check the number located on the end of the valve stems, the bad ones start with the number 72, the good valves start with 75.
    http://greenhulk.net/forums/showthread.php?t=169011
  12. Replies
    35
    Views
    2,834

    Is this a question or statement? You stated...

    Is this a question or statement? You stated earlier that the clutch has only 1 hr on it?
  13. The mistake is that apparently you didn't have...

    The mistake is that apparently you didn't have the correct torx socket remove the exhaust bolt. All is not lost, it should be easy to adapt it to another location such as the Fizzle by fabricating a...
  14. Replies
    17
    Views
    1,095

    I had no problem with my stock IC, went with an...

    I had no problem with my stock IC, went with an external IC and it leaked. I think the stock ICs are made of brass and are very resistant to salt water corrosion, the external ICs are made of...
  15. Replies
    30
    Views
    1,400

    Make sure you have fire, fuel and compression, if...

    Make sure you have fire, fuel and compression, if all are good its most likely a timing issue.
  16. Replies
    17
    Views
    760

    I've never had a problem finding parts for the...

    I've never had a problem finding parts for the older skis. I dont lnow why you would go to the dealer for parts when you can buy them off the internet for much less and have them delivered to your...
  17. Replies
    4
    Views
    227

    Agreed, when in doubt, change it out. Sounds like...

    Agreed, when in doubt, change it out. Sounds like you're trying to skimp on your build tiderider. Build it right the first time and have peace of mind knowing you did it right the first time. The...
  18. I also believe the CRC will not cause the...

    I also believe the CRC will not cause the problems stated. I agree with the Saum700P. Your problem lies elsewhere.
  19. No they're not the same as the SC washers.

    No they're not the same as the SC washers.
  20. Replies
    16
    Views
    1,416

    Never experienced this in thirty years of...

    Never experienced this in thirty years of building engines, maybe I change plugs too often? Here's pic of the side gapping. The plug on the left is before, on the right after. Another tip is...
  21. Replies
    50
    Views
    2,314

    Those are ceramic clutch washers. You will...

    Those are ceramic clutch washers. You will definitely need to have the SC rebuilt. You might have been luck finding the washer if you take the valve cover off. Its made of steel so best bet would be...
  22. Replies
    25
    Views
    2,343

    Thanks you actually have to change the spark...

    Thanks you actually have to change the spark plugs and install a new wear ring to classify as a build thread...
  23. Yes he's referring to the flywheel bolts. To get...

    Yes he's referring to the flywheel bolts. To get the full benefit of the upgraded supercharger, you need an ext IC.
  24. Try the obvious, change spark plugs.

    Try the obvious, change spark plugs.
  25. Replies
    49
    Views
    3,802

    12 years too, started on PWCToday and moved over...

    12 years too, started on PWCToday and moved over here in 2007 when I started wrenching on 4 strokes. First ski was a 96XP.
Results 1 to 25 of 216
Page 1 of 9 1 2 3 4