Search

Page 1 of 3 1 2 3

Search: Search took 1.00 seconds.

  1. The diaphram allows fuel into the carb. With it...

    The diaphram allows fuel into the carb. With it backwards it wasn’t allowing enough fuel in.
    Check the needle arm height.

    Definitely rebuild the carbs and fuel pumps.
    Not enough piston wash on...
  2. Post a picture of the engine with spark plugs...

    Post a picture of the engine with spark plugs removed.
    The cylinder furthest forward is #1.
  3. Oil smoke has a blue tint. Water in the...

    Oil smoke has a blue tint. Water in the combustion camber will be white.

    Is this happening with the craft in the water ?

    With fuel infection you CAN NOT use premix. Oil will not get down to the...
  4. Replies
    10
    Views
    1,436

    FS - Parts TTT Only 1 left.

    TTT Only 1 left.
  5. Replies
    7
    Views
    244

    https://www.watercraftsuperstore.net/?msclkid=1a18...

    https://www.watercraftsuperstore.net/?msclkid=1a18871c792b164e9e06d9cfbfa1aef6&utm_source=bing&utm_medium=cpc&utm_campaign=**LP%20Branded&utm_term=watercraft%20superstore&utm_content=Watercraft%20Supe...
  6. Most of the water cooled the pipe first-then goes...

    Most of the water cooled the pipe first-then goes to exhaust manifold-then into the engine,
    The small hose would let some of the hot water go out. The Polaris engine is self draining through that...
  7. Replies
    18
    Views
    543

    Yes, center carb hose is the return. Yes...

    Yes, center carb hose is the return. Yes -separator-switch hose is supply,goes to front and rear carb, marked 'RES' on sender.
    Yes the sending unit itself has small letters molded into the...
  8. Replies
    6
    Views
    185

    Looks like at some point the 2002 model is listed...

    Looks like at some point the 2002 model is listed as having the "high start" CDI and flywheel. As far as I know there is no CDI available for high start. I think that was also later 02 models and all...
  9. Replies
    22
    Views
    1,465

    The bracket will go on the inside of the hull....

    The bracket will go on the inside of the hull. The jet pump is already a large chunk of metal. So you will pretty much sandwich the hull between metal. Spread the load over a large area of hull...
  10. Replies
    1
    Views
    109

    The 3/4 hose could be routed as needed or get 90...

    The 3/4 hose could be routed as needed or get 90 degree elbows from a hardware store.

    The exhaust hose if I remember correctly is 2 3/4,possibly 2 7/8. I have used silicone 90 degree elbows that...
  11. Replies
    15
    Views
    516

    The black wire at the 12 pin connecter for MFI.

    The black wire at the 12 pin connecter for MFI.
  12. http://parts.polarisind.com/Browse/Browse.asp ...

    http://parts.polarisind.com/Browse/Browse.asp

    5410663
    BUMPER,DRIVE SHAFT
    ...
  13. Replies
    2
    Views
    933

    The nice thing about that cover is it will work...

    The nice thing about that cover is it will work with the factory heads and also could use the Hotseat performance heads.
  14. Replies
    7
    Views
    531

    Welcome to GreenHulk .

    Welcome to GreenHulk .
  15. Replies
    5
    Views
    399

    Also plug wires and boots.

    Also plug wires and boots.
  16. Replies
    1
    Views
    122

    The arm height is measured by placing a straight...

    The arm height is measured by placing a straight edge on the surface of the carb above the arm. Measure .060 inch from straight edge down to button on arm.
    Pop off is 18-20 psi.
  17. Replies
    4
    Views
    359

    Welcome to Green Hulk. For 2 years Polaris used...

    Welcome to Green Hulk.
    For 2 years Polaris used what they call "high start" CDI and flywheel.
    You are lucky enough to have one. You have 2 options- buy used CDI or use a regular CDI that SBT sells...
  18. Replies
    12
    Views
    608

    I have been talking with "xtxracer" he is also a...

    I have been talking with "xtxracer" he is also a member here. He sold some new factory parts a while back,most notably complete Virage seat assemblies. He has LR505's for sale,he might have access to...
  19. Replies
    15
    Views
    767

    Where the red/pur CDI wire attaches should be the...

    Where the red/pur CDI wire attaches should be the ONLY difference in the factory wiring manual.
    There was a TSB to change that.

    Put it back and test for power on the orange or replace the LR.
  20. Those spark plug wires are the type used with the...

    Those spark plug wires are the type used with the update ignition coil- which means it should have the updated ignition.

    The picture showing the front of the engine shows the oil pump block off...
  21. Replies
    68
    Views
    9,826

    When K447 replies to your post, all there is to...

    When K447 replies to your post, all there is to say is "Thank you". No need for a +
  22. Replies
    11
    Views
    2,189

    The SLX should see 6700 and depending on rider...

    The SLX should see 6700 and depending on rider weight, like 63-65 mph.
    I would try it in the SLTX,that would be the only way to say for sure. And of course, if you like it.
  23. Replies
    11
    Views
    2,189

    Its actually an easy job with the right tools. ...

    Its actually an easy job with the right tools.

    Only the impeller jets replaced.
    After removing the pump stator-remove cone from rear- impeller shaft will be visible-there are 2 flat surfaces,...
  24. Replies
    11
    Views
    2,189

    I use the Nujet 7.0 in my 2001 SLX. It is the...

    I use the Nujet 7.0 in my 2001 SLX. It is the best impeller I tried in it. It deffinetly had the best top speed, by 1 - 1.5 mph , even over the Polaris 7.0 impellers. My SLX also has the R&D 650...
  25. Yes, the second post is correct.

    Yes, the second post is correct.
Results 1 to 25 of 72
Page 1 of 3 1 2 3