Search

Type: Posts; User: mwhc

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. What do you think is going on? I've seen...

    What do you think is going on? I've seen multiple 300's that ended up leaking supercharger oil but fixed them before anything catastrophic
  2. Replies
    9,246
    Views
    509,340

    With her gun awareness there's no way she was...

    With her gun awareness there's no way she was missing at that range. One could only assume drugs/rage/adrenaline kept him standing as long as he did
  3. Replies
    3
    Views
    107

    You'll have it enough apart at that point to just...

    You'll have it enough apart at that point to just take it out and not fight it
  4. Replies
    11
    Views
    560

    Poll: Lots to consider..... did it sit with water in it...

    Lots to consider..... did it sit with water in it for a long time? Cams rust quick (I know personally) head is expensive, can you do it yourself? Etc etc. Its probably a minimum of 5hrs to pull...
  5. Replies
    27
    Views
    677

    RWD... reading while driving, partially my fault...

    RWD... reading while driving, partially my fault too[emoji41][emoji1787]
  6. Replies
    27
    Views
    677

    I'm 90% sure their "low octane" tune is for...

    I'm 90% sure their "low octane" tune is for California 91 octane and NOT 87. Its supercharged with 14-17psi you can only pull so much timing out before you run into other issues. I'd check with...
  7. Replies
    4
    Views
    142

    Could have been rod side clearance let me look...

    Could have been rod side clearance let me look when I get home
  8. Replies
    4
    Views
    142

    Look in the manual I believe there is a spec for...

    Look in the manual I believe there is a spec for clearance on the thrust bearings when assembling the engine. I suppose you could interpret that as end play once fully assembled.
  9. Replies
    2
    Views
    144

    IMO Older skis it's usually not worth the cost to...

    IMO Older skis it's usually not worth the cost to replace the engine when you can find one that runs for the same price. Newish ones are SO expensive to fix it's a tuff call. If you're thinking...
  10. Replies
    91
    Views
    6,766

    Worst case scenario I know kaza racing makes...

    Worst case scenario I know kaza racing makes custom ones.
  11. Replies
    6
    Views
    259

    Ah yea I would definitely go aluminum then and...

    Ah yea I would definitely go aluminum then and never look back
  12. Replies
    6
    Views
    259

    Well you dropped a link to square tube so I'm not...

    Well you dropped a link to square tube so I'm not sure if that's right but I usually just measure length/height of whatever your plastic ones are and order something similar in 1/4" aluminum........
  13. Replies
    6
    Views
    259

    I've made a couple for my ultras and svho's using...

    I've made a couple for my ultras and svho's using aluminum. Is that not an option for ya?
    463248
  14. Replies
    34
    Views
    1,232

    The "ultra" hull is the same size supercharged or...

    The "ultra" hull is the same size supercharged or not. I would say the ultra is larger and more stable then any of the older vx models and definitely more rough water capable then a vx.

    You are...
  15. Thread: intake mod

    by mwhc
    Replies
    6
    Views
    325

    Either one of the 2 big black air hoses. If you...

    Either one of the 2 big black air hoses. If you cant figure out which one is an air hose then dont do it. Btw itll fill your engine up with water if you manage to roll it
  16. Thread: intake mod

    by mwhc
    Replies
    6
    Views
    325

    Pull the rubber out of the front of the airbox...

    Pull the rubber out of the front of the airbox and stuff one of the black breather tubes straight into it...... hahaha its loud AF and not fun to cruise on but you can easily reverse it back
  17. Replies
    4
    Views
    260

    They are not compatible. 310 has a knock sensor.

    They are not compatible. 310 has a knock sensor.
  18. Replies
    91
    Views
    6,766

    100% certain there is a spec for that...

    100% certain there is a spec for that driveshaft..... but I cant remember what it is off the top. I know crazy a$$ reid had it burried in that monster thread he had a while back
  19. Thread: Versi Plugs

    by mwhc
    Replies
    2
    Views
    210

    FS - Parts $20 for both I'll pay shipping...

    $20 for both I'll pay shipping...
  20. Replies
    9,246
    Views
    509,340

    Maybe it's not a "real" gun question but can...

    Maybe it's not a "real" gun question but can anyone recommend a real good break barrel pellet gun? Anyone can research/google but us here I feel like dont bs and will give an honest answer. Thanks...
  21. Replies
    1
    Views
    173

    They do. There's always the tradeoff though

    They do. There's always the tradeoff though
  22. Replies
    14
    Views
    892

    Yea and usually once the valve gets a full heat...

    Yea and usually once the valve gets a full heat soak in it, it will pop off a touch lower and close a bit slower.

    I have a billet aluminum reusable oil filter with a different bypass system in...
  23. Replies
    4
    Views
    319

    SOLD I do have 2, $75 each plus shipping? Message...

    I do have 2, $75 each plus shipping? Message me.462150
  24. Replies
    4
    Views
    319

    SOLD I believe I have 2 but for sure 1. How about $75...

    I believe I have 2 but for sure 1. How about $75 you pay shipping?
  25. Thread: pulley 300lx

    by mwhc
    Replies
    9
    Views
    525

    Ok so I'm not say the theory is wrong. Who here,...

    Ok so I'm not say the theory is wrong. Who here, personally (not someone you know) has shredded a belt in a race?
Results 1 to 25 of 171
Page 1 of 7 1 2 3 4