Search

Type: Posts; User: Lowryder898

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    71
    Views
    1,815

    Im assuming that is what caused my engine failure.

    Im assuming that is what caused my engine failure.
  2. Replies
    71
    Views
    1,815

    2 & 3 Discharge lines.

    2 & 3 Discharge lines.
  3. Replies
    71
    Views
    1,815

    Ok I may have overlooked some things. Apparently...

    Ok I may have overlooked some things. Apparently the aft 2 cylinder water lines have little to no flow. How I overlooked it i have no idea.
  4. Good luck man. Maybe there is hope for me as well.

    Good luck man. Maybe there is hope for me as well.
  5. Replies
    71
    Views
    1,815

    So I found this on a ultra forum. burnt a hole...

    So I found this on a ultra forum. burnt a hole throught he rear piston from a lean condition. I checked all the carbs and diaphrams and sliders, no dirt at all.
    Then I found the fuel pump could suck...
  6. I didnt realize they came with a step on the...

    I didnt realize they came with a step on the back. Mine diest have one. 464325
  7. The fittings on the top are for the bilge. Mine...

    The fittings on the top are for the bilge. Mine broke when I rebuilt the pump. What a pain to replace as far as finding something that fits.464305
  8. Replies
    71
    Views
    1,815

    Yeah I saw that it was missing and then I...

    Yeah I saw that it was missing and then I remembered your thread. I ordered OEM o rings from cycle nation for 2.60 apiece. I haven't move the tps sensor. I left it on the mount but I probably should...
  9. Replies
    71
    Views
    1,815

    Yes 464279

    Yes 464279
  10. Replies
    71
    Views
    1,815

    I did. Everything was out and cleaned and the...

    I did. Everything was out and cleaned and the engine parts are on the way. I just need to flush the rails. Can you buy just the o rings for these jets?
  11. Replies
    71
    Views
    1,815

    Both plates of the fuel pump had build up....

    Both plates of the fuel pump had build up. Cleaned with a bit of red scotch brite and put a thin coat of o ring lube on the metal surfaces before reinstallation.
  12. Replies
    71
    Views
    1,815

    #2 looked similar. #1 had more buildup and grit...

    #2 looked similar. #1 had more buildup and grit on the backside. Other than that no horrible. Fuel pump464272464273464274464275
  13. Replies
    71
    Views
    1,815

    Took # 3 valve and filter out. There was build up...

    Took # 3 valve and filter out. There was build up on the carb wall on one side.464269464270464271
  14. The tale of 2 skis.

    The tale of 2 skis.
  15. Replies
    71
    Views
    1,815

    If they are we have some tools at my work that...

    If they are we have some tools at my work that should be able to remove them. Thanks for the heads up
  16. Replies
    71
    Views
    1,815

    No. Fri at the earliest. Not much time during the...

    No. Fri at the earliest. Not much time during the week. Hopefully tomorrow.
  17. Replies
    71
    Views
    1,815

    Dirty and dark. Piston is out and the rings are...

    Dirty and dark. Piston is out and the rings are stuck on the exhaust side with lots of scoring. I was expecting the plug to lighter if it was lean. Just thinking until I get parts
  18. Replies
    71
    Views
    1,815

    Here are the plugs. It died WOT the middle plug...

    Here are the plugs. It died WOT the middle plug was #3 not sure about the other 2.464180
  19. Replies
    0
    Views
    147

    Vx 110 lacking power

    Good afternoon. I have a 2009 vx that has @90 hours. I have had it since September and have had more or less the same issue. It will not go past 40mph or 7k. I have replaced the airbox with a cone...
  20. Replies
    71
    Views
    1,815

    Are you referring to the square covers on the...

    Are you referring to the square covers on the outboard/back side?
  21. Replies
    71
    Views
    1,815

    Can I pressurize the carbs on the bench? Im going...

    Can I pressurize the carbs on the bench? Im going to open them to see if they are dirty anyway but to eliminate 1 thing would be a start.
  22. Replies
    71
    Views
    1,815

    Who now that is a coincidence. Yeah the tree...

    Who now that is a coincidence. Yeah the tree branch fell while changing the trailer skids. Grazed my brother and did a little damage to the Yamaha. 2020
  23. Replies
    71
    Views
    1,815

    Not yet though tempting. Too early and too...

    Not yet though tempting. Too early and too stubborn. I live south of Sav Ga.
  24. Replies
    71
    Views
    1,815

    Will do. Just thinking wtf is next. I usually...

    Will do. Just thinking wtf is next. I usually dont have much time during the week so I end up with too much time to think about it. Hell I just fixed the hull. Cursed. Last 3 months....
  25. Replies
    71
    Views
    1,815

    Im wondering if it is the carbs. The first time...

    Im wondering if it is the carbs. The first time it was #1 and the second #3. I know ill have to check. I followed the spec for routing the oil lines so that should be good. Should
Results 1 to 25 of 41
Page 1 of 2 1 2