Search

Type: Posts; User: Mockingee

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    2
    Views
    85

    I could be wrong but I would think people would...

    I could be wrong but I would think people would have bad sensors with good housings they would be willing to sell reasonably.

    If not, you could look at having someone 3D print one for you. Iím not...
  2. You should measure it while pumping and with the...

    You should measure it while pumping and with the original fuel pressure regulator.
  3. Replies
    11
    Views
    273

    This is very interesting. I’m anxious to hear how...

    This is very interesting. I’m anxious to hear how the voltage tunes in. It seems odd to me that the universal sensor turns 180 degrees. I’m wondering if only part of that rotation is actually varying...
  4. Replies
    19
    Views
    541

    Hopefully it’s not the motor. Speaking from...

    Hopefully it’s not the motor. Speaking from experience that sucks.
  5. Replies
    19
    Views
    541

    Your motor sounds much better without the pump....

    Your motor sounds much better without the pump. In the video it has a loud ticking but I’m guessing the mic is picking up the injector noise more than the other, lower frequency noises.
  6. Replies
    4
    Views
    441

    Sounds like the stator connector which plugs into...

    Sounds like the stator connector which plugs into the EMM.
  7. Replies
    10
    Views
    427

    Glad you got it figured out, and thanks for...

    Glad you got it figured out, and thanks for posting the results.
  8. The so called priming noise you hear is most...

    The so called priming noise you hear is most likely the MFI waking up.
  9. Replies
    19
    Views
    541

    The engine might make a hissing noise as it pulls...

    The engine might make a hissing noise as it pulls air through the reeds but that shouldn’t make it hard to turn. That’s the only thing I can think off.
  10. Replies
    6
    Views
    162

    As K447 pointed out, reinforcing the fuel pump...

    As K447 pointed out, reinforcing the fuel pump regulator is not optional. You should NOT drive it again before the repair. It’s not if it falls out it’s when.
  11. Replies
    19
    Views
    541

    I also thought it sounded sluggish. I wondered if...

    I also thought it sounded sluggish. I wondered if it was just my ears.

    With no spark plugs and no binding from the pump the
    engine should be fairly easy to turn by hand. Without plugs there...
  12. Replies
    19
    Views
    541

    Since the motor was locked up when you got it I...

    Since the motor was locked up when you got it I would suspect the motor. Mine was acting like that when the crank bearings let go, but it also sounds like piston seizure. The first thing is to make...
  13. Looks to me like pieces of bearing. Check the rod...

    Looks to me like pieces of bearing. Check the rod and crank bearings.
  14. Replies
    10
    Views
    427

    Did you get sparks when you shorted the solenoid?

    Did you get sparks when you shorted the solenoid?
  15. Replies
    10
    Views
    427

    If you properly shorted the solenoid and the...

    If you properly shorted the solenoid and the starter didnít spin you are left with, bad battery, bad connection (ground or large red positive), bad starter, or possibly a stuck bendix. Can u turn the...
  16. The regulator still being attached is not good...

    The regulator still being attached is not good enough. Unless it has been reinforced it will fall off.

    If I’m wrong I’m sure one of the experts will correct me but without consulting the wiring...
  17. When you had the fuel pump out did you check to...

    When you had the fuel pump out did you check to see if the fuel pressure regulator had been reinforced, or have you done that previously? I’m wondering if that was your bogging issue. Running a FICHT...
  18. Replies
    40
    Views
    1,175

    Wait and see what the experts say about it but I...

    Wait and see what the experts say about it but I assume, like you, that if it’s fuel resistant it should be OK. I was afraid it was the cheap stuff you referred to.
  19. Replies
    40
    Views
    1,175

    I thought RTV in a two stroke engine was a no no....

    I thought RTV in a two stroke engine was a no no. I was always told to use a special sealant such as 3 Bond.
  20. There is a pop off valve in there. Specs if I...

    There is a pop off valve in there. Specs if I remember correctly are 3-5 psi. The proper way to test It is to use a small pump with a low pressure gauge. I don’t own one so I had my local small...
  21. Replies
    15
    Views
    551

    It seems odd to me that fuel pressure increases...

    It seems odd to me that fuel pressure increases when revving. Why would that happen?
  22. Replies
    70
    Views
    2,371

    View Post

    Iím thinking pieces of the piston skirt came up through and thatís what beat up the top of the piston, but I canít imagine why the piston skirt came apart like that. Maybe it was a defective...
  23. Replies
    25
    Views
    592

    The wires were fastened to the inside of the hull...

    The wires were fastened to the inside of the hull at one time. You may still have the hooks on the wires and you may be able to see where they were stuck on the hull.
  24. Since the choke helps it must be lean.

    Since the choke helps it must be lean.
  25. Replies
    16
    Views
    557

    I also have one that does that. It’s worth...

    I also have one that does that. It’s worth keeping because it’s better than nothing. You can always use the lanyard to shut it off, and if HiPeRcO figures them out we can get them repaired.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4