Search

Page 1 of 8 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    5
    Views
    258

    WTB Excellent seller,highly recommended!!!!!

    Excellent seller,highly recommended!!!!!
  2. Replies
    7
    Views
    494

    The correct non stock replacement TB is Bosch 280...

    The correct non stock replacement TB is Bosch 280 750 009, using a FelPro gasket #61092 with 4 - 60mm bolts. I've been using this TB on my turbo ski for the pass 3 years. No issues to date.
  3. FS just a bump for you. got the prop. looks great,...

    just a bump for you.
    got the prop. looks great, just like you described.
  4. Update : I bought sum 40mm long bolts and they...

    Update :
    I bought sum 40mm long bolts and they were to short. Bought 50mm bolts and they were perfect.
    Had dealer reset tps for 40 bucks.
    The bosch throttle body worked perfectly
    I want to...
  5. Bosch TB 0 280 750 009, Felpro gasket 141022 and...

    Bosch TB 0 280 750 009, Felpro gasket 141022 and shorter stainless steel bolts, M6x40.

    https://www.autozone.com/fuel-delivery/throttle-body-unit/bosch-throttle-body-unit-0280750009/388001_0_0...
  6. Replies
    16
    Views
    2,801

    drop the tabs some

    drop the tabs some
  7. Replies
    7
    Views
    1,036

    Were the injectors new? Sounds like the...

    Were the injectors new? Sounds like the injectors flooding the motor by leaking the residual fuel pressure into the intake when its turned off. When it does it again try holding full throttle and...
  8. Replies
    37
    Views
    12,754

    I have a 09 gtx 255 that was throwing a map...

    I have a 09 gtx 255 that was throwing a map sensor code p0106. New map sensor installed and still had the code pop up and went into limp mode. I installed the bosch 0280750009 throttle body and...
  9. Replies
    10
    Views
    1,083

    You need a torque wrenc,holding plate and gear...

    You need a torque wrenc,holding plate and gear holding tool to do it right and most accurate..BUT you can do it in the ski if you have a torque wrench that can record highest slip by locking the...
  10. Replies
    37
    Views
    12,754

    Ah I guess I was lucky then. I didn’t have to...

    Ah I guess I was lucky then. I didn’t have to reset my Tpms. I used the original gasket and just cut off the tabs
  11. Replies
    37
    Views
    12,754

    I run them . Didn't reset or repositon anything...

    I run them . Didn't reset or repositon anything ski runs the same as it did with the overpriced stock one .
    I believe the valve is stainless . No issues with it at all !
  12. Replies
    19
    Views
    2,099

    Back when he was mostly doing stand-up skis, we...

    Back when he was mostly doing stand-up skis, we would see similar topics (on x-h2o). Bottom line - he gets slammed in the summer all the way through October/November. We are now getting near World...
  13. SOLD Yes it would raise your Limiter and allow your to...

    Yes it would raise your Limiter and allow your to spin the motor higher and gain more boost from you XX. I would recommend retainers also. Spin it 8550 and have fun. Riva ECU is mapped for Delphi...
  14. Replies
    4
    Views
    902

    Cp rings will not work on wsm or oem, Rik are...

    Cp rings will not work on wsm or oem, Rik are just as good as oem if not better.
    You should get a lot more hrs out of them than 45. What was the ring gapped to?
  15. Thread: No Compression

    by Sanfish
    Replies
    35
    Views
    3,719

    Don't bother with a leak-down, its pretty obvious...

    Don't bother with a leak-down, its pretty obvious its one of two things. Start off by pulling head and inspect valve seats...if they are good, you will need to re-ring (or new pistons/rings)
  16. Replies
    16
    Views
    1,541

    A bolt being ripped out is not a hull compromise....

    A bolt being ripped out is not a hull compromise. I had an 08 RXTX, I know when a hull is compromised.
  17. Great job .... throw some more boost at it ....

    Great job .... throw some more boost at it . Bigger prop and some race fuel..
  18. https://youtu.be/FnXNnhs3FAo This was a few...

    https://youtu.be/FnXNnhs3FAo

    This was a few weeks ago .. not a race but the gpr got a bit boring doing 60mph on such a nice fast river . So after a minute 20 i stepped it up a notch .. then it was...
  19. Replies
    15
    Views
    3,077

    Yes. I had it happen to Rays 2007 RXT. Luckly had...

    Yes. I had it happen to Rays 2007 RXT. Luckly had 2 bent valves and nothing else. Sent off to SLow and had head done and then New Chain, Arp Flywheel and cam sprocket bolts.
  20. Replies
    251
    Views
    39,247

    i jist want a reliable worry free SCer ...

    i jist want a reliable worry free SCer[/QUOTE]

    its called a turbo ...... \\:D/
  21. Replies
    17
    Views
    2,966

    I stabbed 2 holes in my hand installing those...

    I stabbed 2 holes in my hand installing those damn clips. Blood and sweat definitely in that engine, lol. After 45 minutes on the first one, they rest were done in about another 45 min, lol.
  22. Replies
    444
    Views
    51,179

    I must say. You are a shit talker now. Its funny....

    I must say. You are a shit talker now. Its funny. I guess you have your reasons and you have owned seadoo's So at least you have owned both. But still funny. I like the GP1800 ski and will be buying...
  23. i think i have a scat 3 blade laying around that...

    i think i have a scat 3 blade laying around that speedfreaks tweeked back in the day, i have no more ski so i should probly sell it LOL
  24. Wow a used prop is normally $150 so it really...

    Wow a used prop is normally $150 so it really isnt that bad of a deal.
  25. Dave is the man! Spoke to him as soon as I saw...

    Dave is the man! Spoke to him as soon as I saw this OP last thread. Ordered impeller onn a Saturday was shipped Friday. Will have results when I'm back from vaca. Was awesome to deal with though!
Results 1 to 25 of 179
Page 1 of 8 1 2 3 4