Search

Type: Posts; User: BMist371

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    12
    Views
    364

    Heat the pump housing and freeze the ring. Heat...

    Heat the pump housing and freeze the ring. Heat gun works well.
  2. Replies
    138
    Views
    6,820

    Other than oil being overfilled, im out of ideas...

    Other than oil being overfilled, im out of ideas for you. But I am hanging around for the solution. I like to learn as much as anyone. It sounds like an issue with the tune in my opinion. Something...
  3. Replies
    71
    Views
    5,891

    Start tearing down pump housing in the back of...

    Start tearing down pump housing in the back of the ski then. Check your wear ring for damage and check the impeller for damage. The veins behind the impeller should be inspected for damage too, as...
  4. Replies
    71
    Views
    5,891

    Typical things that seem to rob speed can be...

    Typical things that seem to rob speed can be overfilled oil, a boost leak, plugs, or even a bad coil. The fact that your rpms seem to be ok would suggest something more related to the pump though....
  5. Replies
    138
    Views
    6,820

    If you are still down on rpm, check your oil and...

    If you are still down on rpm, check your oil and see if you are overfilled. Should be between the 2 bends. I accidently overfilled mine in the off season and it robbed 200rpm. If it's overfilled,...
  6. Replies
    122
    Views
    6,668

    I have a 4 inch intake and a covered hole in the...

    I have a 4 inch intake and a covered hole in the back of the ski. Airflow is not my issue. Runs within 40 rpms of itself with the seat on or off.
  7. Replies
    122
    Views
    6,668

    I agree, I think the majority of the variables...

    I agree, I think the majority of the variables are mainly in the props. No 2 props are alike. I'm stage 2, plus exhaust, waterbox, IC piping, and IC. I hit 79 today at 70 degrees and 1100ft...
  8. Can confirm that IBR will trip with low voltage....

    Can confirm that IBR will trip with low voltage. Check the yellow wires coming from the stator and check your grounds as well. Sounds like an electrical issue for sure. I had a bad battery and had...
  9. Replies
    122
    Views
    6,668

    You're spot on where you should be then. Don't...

    You're spot on where you should be then. Don't sweat it. I bet in saltwater, at sea level, with the current, you'd be doing 77+.
  10. Maybe going airborne tricked the tops valve to...

    Maybe going airborne tricked the tops valve to think you were inverted and shut down the ski?
  11. Replies
    122
    Views
    6,668

    Do you ride on a lake? Or saltwater? Keep in...

    Do you ride on a lake? Or saltwater? Keep in mind, if you're in a still body of water like a lake, some of these wild speeds people post are also generated at sea level, in saltwater, going with the...
  12. Replies
    122
    Views
    6,668

    75 at 2 bars is pretty average. Need to unlock...

    75 at 2 bars is pretty average. Need to unlock the RPMs to go faster.
  13. Replies
    82
    Views
    7,546

    I don't functionally use my hole for a pylon or...

    I don't functionally use my hole for a pylon or anything. Mine is covered in frogzskin. I think if you intend to use the pylon, I would not cut the hole larger regardless for structural purposes.
  14. Replies
    82
    Views
    7,546

    Anyone looking to eliminate parts, this coupler...

    Anyone looking to eliminate parts, this coupler will eliminate the need for the 3-4" stack adapter and bolt directly onto your SC. Just need a Flame Arrestor, pipe, and clamps. Less parts, less cost,...
  15. Replies
    2
    Views
    404

    I find the suction cup mount pretty versatile. I...

    I find the suction cup mount pretty versatile. I use a floaty and a case that floats as well around my gopro and that is enough to float the suction mount. I also tether it usually. I'm here for some...
  16. Replies
    82
    Views
    7,546

    Apologies, I see you are pointing to another...

    Apologies, I see you are pointing to another hole. Is that the hole created by the original 90* pipe being removed from the intake? If so that hole just goes up to your intake box. Hard to see as...
  17. Replies
    82
    Views
    7,546

    I use a catch can so I no longer have that hole....

    I use a catch can so I no longer have that hole. All 300 machines need one. Even factory. You'll cram your whole intake tract full of blow by and coat your intercooler increasing your IAT. Buy one,...
  18. Replies
    82
    Views
    7,546

    Upgr8 makes the 90* coupler, the filter and 3-4"...

    Upgr8 makes the 90* coupler, the filter and 3-4" supercharger stack adapter can be found in the greenhulk store. Some people like to just buy a 3-4" 90* coupler and be done with it. I would love to...
  19. Replies
    82
    Views
    7,546

    Haven't been on the water yet. Waiting on my...

    Haven't been on the water yet. Waiting on my intake grate. I'm not bold enough to ride the junk grate at 80 yet. I am also using a strainer. No IMUK. I'll do that when I take the head off next season...
  20. Replies
    82
    Views
    7,546

    We see 100* a few times a summer but 90-95* is...

    We see 100* a few times a summer but 90-95* is pretty normal. That and the humidity is why I opted for the Fizzle. Try and defeat some of the heat. If I don't see 80, well, i'm going in a different...
  21. Replies
    82
    Views
    7,546

    Right now it's a Fizzle Supercooler, free flow...

    Right now it's a Fizzle Supercooler, free flow exhaust, waterbox, catch can, intake, and IC hard piping with a stage 2 tune from Riva. Wanted to do another route but the heat soak was crazy with the...
  22. Replies
    82
    Views
    7,546

    I don't think I have posted a recent pic of mine...

    I don't think I have posted a recent pic of mine since I finished up my stuff during the off season.
  23. Mine is at 14 hrs and the dust line is incredibly...

    Mine is at 14 hrs and the dust line is incredibly light. I'm just happy to get it switched for the new part so ill have some extra wear to work with on the new seal, plus having a new seal. Knock on...
  24. I dropped mine off to have my intake grate recall...

    I dropped mine off to have my intake grate recall done and asked them to check the carbon seal and ended up getting a freebie carbon seal anyways....Mine had a little black dust line, but not much. I...
  25. Replies
    11
    Views
    479

    If all they do is replace it without realigning...

    If all they do is replace it without realigning the motor and properly shimming it, expect it to happen again.
Results 1 to 25 of 165
Page 1 of 7 1 2 3 4