Search

Type: Posts; User: Saum700p

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. 13/20 with an 8,000 tune

    13/20 with an 8,000 tune
  2. Id suggest sucking the fuel out. You have to pull...

    Id suggest sucking the fuel out. You have to pull the pump back out to drill for the return ...and you have to remove the stock regulator.
  3. Replies
    12
    Views
    464

    I've blown up one Solas in the middle of mobile...

    I've blown up one Solas in the middle of mobile bay. Nothing around to suck up and in deep water. Contact your supplier to file a claim.
  4. Interested in some data from this. +1psi, is...

    Interested in some data from this. +1psi, is that from the velocity stack style front? Difference vs the velocity stack with the CAI kit. And second the IAT's vs. Stock housing on a hot engine. ...
  5. Replies
    36
    Views
    1,857

    Keep us posted. this will be the first new Fx...

    Keep us posted. this will be the first new Fx that I know of running the vxr cams.
  6. Replies
    166
    Views
    26,124

    You can start by pulling that 11/15 out of...

    You can start by pulling that 11/15 out of there.. I tried it it's trash. You are better off with a stock impeller pitched then that all day.
  7. Replies
    8
    Views
    469

    Im running the ones from the older worx fx/fz on...

    Im running the ones from the older worx fx/fz on my gp and vxr. The mounting holes are the same. Not sure if the riva are better, but the worx are more than enough for me and i'm running them in...
  8. Problem is the damage to the hub from the old...

    Problem is the damage to the hub from the old clutches.
  9. Replies
    6
    Views
    280

    Time the cams with the dots on the cam and the...

    Time the cams with the dots on the cam and the middle cap arrows. They should look identical to the the other ones by eye. You're good.
  10. Replies
    7
    Views
    437

    I have one in New Orleans, 23 hours pulled from...

    I have one in New Orleans, 23 hours pulled from 2018.
  11. Replies
    6
    Views
    280

    Tape should be fine. I put some red loctite on...

    Tape should be fine. I put some red loctite on mine.
  12. Replies
    6
    Views
    280

    Cam Gear Tq. 24nm or 17.7 ftlb. Cam Caps...

    Cam Gear Tq. 24nm or 17.7 ftlb. Cam Caps 16nm or 11.8 ftlb. Red lock tight on the cam gear oil on the cam caps. Set all the cam caps hand tight and walk them down. Manual doesn't list an...
  13. Replies
    56
    Views
    3,904

    ouch...

    ouch...
  14. Replies
    2
    Views
    405

    I believe they were smaller then that, off the...

    I believe they were smaller then that, off the interior pump lines were less then 10 if I remember right
  15. I don't have a picture of it but I used a squall...

    I don't have a picture of it but I used a squall and grinder to notch out my plugs till the plate gasket seated up tight then put l little 5200 on it when it was finished to hold it in place.
  16. The quality definitely isn't there with he pump...

    The quality definitely isn't there with he pump seal. I don't know why they can't just fill the voids on the grate with the stuff and leave it in there sell it as a package.
  17. Ill second the clutch... 50 mph 6,000 rpm is...

    Ill second the clutch... 50 mph 6,000 rpm is what I had when mine went out. Just pull the tube on the front of the supercharger and spin the impeller with your finer. Spins both ways? You need a...
  18. Replies
    2
    Views
    183

    I have worx on mine they bite plenty hard. I even...

    I have worx on mine they bite plenty hard. I even have them in the up position. I got a good bit of side bite with my Dean's cut ride plate. Might want to look into that kills two birds with one...
  19. Replies
    3
    Views
    347

    Possibly running too cold. What are the temps at...

    Possibly running too cold. What are the temps at your location. I took mine out in the late winter months and had some condensation in the oil cap. After it warmed up they are gone.
  20. Replies
    32
    Views
    2,657

    Copy his are having leaking issues? Asking for a...

    Copy his are having leaking issues? Asking for a buddy. I went tail, and i'm having no issues but his ski is dumping boost at the top end for some reason. either this or clutch going out but after...
  21. Replies
    5
    Views
    311

    Air filter, tune, and impeller is a great start. ...

    Air filter, tune, and impeller is a great start. Consider Dean's tunes they are excellent, and he does a tune and impeller combo.
  22. Thread: Vxr cams

    by Saum700p
    Replies
    11
    Views
    694

    I saw several mph out of the cams and...

    I saw several mph out of the cams and reflash/repitch on mine. doing cams also puts you at the max of the fuel system so you're going to need to do a pump and regulator. Get with your tuner to set...
  23. Replies
    22
    Views
    1,677

    Dean makes a plate which i've seen at 82+ no...

    Dean makes a plate which i've seen at 82+ no porpoising. Might want to try giving him call.
  24. Those mods are great, I have done them on both of...

    Those mods are great, I have done them on both of my skis. But you are not going to unlock any power until you tune the ski. It will be factory speed limited. I suggest the air intake and filter,...
  25. Replies
    22
    Views
    1,677

    Trim extender is not going to fix that. There...

    Trim extender is not going to fix that. There have been a few people complaining about the Riva plate porpoising unfortunately.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4