Search

Type: Posts; User: grumpy_steven

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds; generated 38 minute(s) ago.

  1. Replies
    17
    Views
    707

    Don't know if this would work with a fly-by-wire...

    Don't know if this would work with a fly-by-wire throttle, but it's a simple solution that's worth looking into. Years ago, on a school trip, I rented a snowmobile. The top speed was "governed" by...
  2. Not sure about your ski, but a lot of the hull...

    Not sure about your ski, but a lot of the hull parts are made from colored plastic with a layer of clearcoat. Paint might not hold up very well.

    Why not shop around for good clean parts? A lot...
  3. Replies
    12
    Views
    290

    Key thing now is to remove it without damaging...

    Key thing now is to remove it without damaging that mid-wall. The bearing seal holds back the water pressure from the jet pump, so it needs to be a good seal. If you do any damage to the mid-wall,...
  4. Replies
    12
    Views
    290

    How about a little water to dissolve the salt? ...

    How about a little water to dissolve the salt? I'm not sure how you'd soak those bolts. But I've had some luck freeing up salt-bound parts by soaking them in water. After all, water does dissolve...
  5. Replies
    17
    Views
    707

    I did it on a Kawasaki. I only had to swap the...

    I did it on a Kawasaki. I only had to swap the motor, intake, exhaust, ECU, wiring harness and impeller.
  6. Ultra 310

    Part #11005-0630 (2014-2019 Ultra 310)






    Height between mating surfaces: 3.7 inches
  7. Ultra 300

    Part #11005-3770 (2011-2013 Ultra 300)





    Height between mating surfaces: 3.7 inches
  8. Ultra 250 / Ultra 260

    Part #11005-3766 (2007-2008 Ultra 250, 2009-2010 Ultra 260)




    Height between mating surfaces: 3.7 inches


    Overall height: 4.57 inches
  9. STX-15F / Ultra LX

    Part #11005-3761 (2004-2010 STX-15F, 2007-2008 Ultra LX)

    Height between mating surfaces: 3.44 inches

    Overall height: 4.31 inches

    Difference from STX-12F: Deeper water jacket. Exhaust-side...
  10. STX-12F

    Part #11005-3758 (2003-2007 STX-12F)

    Height between mating surfaces: 3.44 inches

    Overall height: 4.31 inches

    http://greenhulk.net/forums/attachment.php?attachmentid=457355&stc=1
    ...
  11. Kawasaki 4-Stroke Cylinder Identification

    There are several different cylinders used on the Kawasaki 4-stroke motors. They all look similar, but there are differences that one might not readily notice.

    I've seen ads for cylinders that...
  12. Replies
    5
    Views
    464

    FS - Parts Think twice before trying to part out a 12F...

    Think twice before trying to part out a 12F motor. I had the same story, a pair of 12F motors. Had no problem selling a running motor for a decent price. Tried parting out the second motor. The...
  13. If you flush the motor after each ride, you'd be...

    If you flush the motor after each ride, you'd be surprised at how clean the water passages are, even in saltwater operation. I've taken apart a few of these motors (used in salty NY waterways) and...
  14. Don't think you'll find any barnacles or marine...

    Don't think you'll find any barnacles or marine growth inside the motor.

    You will find salt and silt buildup.
  15. Replies
    3
    Views
    151

    WTB - Parts I had a really clean set on ebay. I'll PM the...

    I had a really clean set on ebay. I'll PM the link.
  16. Replies
    3
    Views
    151

    WTB - Parts FYI - they are not the same. Which model do you...

    FYI - they are not the same. Which model do you have?
  17. Replies
    21
    Views
    1,177

    Have you tried new plugs? I haven't yet had the...

    Have you tried new plugs? I haven't yet had the problem with my 09 FXHO, but the MR-1 motors seem to have a common problem. A spark plug or two will just go bad without warning (even brand new...
  18. Replies
    6
    Views
    381

    Hey Steve... Not sure if that's accurate about...

    Hey Steve...

    Not sure if that's accurate about the e-box. I just put the motor from a 97 1100ZXi into a 2001 1100STX-DI hull. I used the e-box/igniter from the ZXi and the wiring harness and...
  19. Replies
    11
    Views
    385

    The waterboxes are pretty pricey, and the newer...

    The waterboxes are pretty pricey, and the newer ones cost even more and are harder to find. If your plan doesn't work out, it's wasted money. With my idea, if it doesn't work out, you can just...
  20. Replies
    11
    Views
    385

    See my Kawasaki build thread (link below). The...

    See my Kawasaki build thread (link below). The older 15F waterbox had a wider output pipe, and a second waterbox was used to reduce noise. On this build, I only used the single waterbox. It...
  21. Replies
    1
    Views
    947

    Great Deal

    Yamaha cylinder head includes the nipples:
    ...
  22. 2-Stroke I once tried to split the two halves of a Yamaha....

    I once tried to split the two halves of a Yamaha. The glue that holds to top and bottom together is very strong, and I did a lot of damage to the hull trying to separate the pieces. If I had to...
  23. Replies
    28
    Views
    1,674

    Doesn't look bad to me. Is it grooved, or is it...

    Doesn't look bad to me. Is it grooved, or is it just polished from rubbing against the seals?

    The more important thing to check is the internal splines. That's what goes bad on these. They wear...
  24. I didn't cut open that sealed bottom section, but...

    I didn't cut open that sealed bottom section, but based on the weight of the part and how light shines through it, I'm pretty sure there's some sort of filter inside.

    I've owned a 2006 SX230HO...
  25. And finally, the cartridge comes out of the...

    And finally, the cartridge comes out of the bottom section:

    http://greenhulk.net/forums/attachment.php?attachmentid=456334&stc=1
    ...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4