Search

Type: Posts; User: beekermartin

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Should I clean the carbon off of these pistons...

    Should I clean the carbon off of these pistons before reinstalling them? Is there an easy way to do it? I was thinking of laying them tops down in a plastic container with Seafoam?
    452616
  2. Replies
    10
    Views
    161

    You can keep checking eBay and the classifieds...

    You can keep checking eBay and the classifieds here. SBT is the only other place I know of that sells remanufactured housings. Did you inspect the wear ring on your housing?

    The motor in the...
  3. Replies
    10
    Views
    161

    That was then and I couldn't find anything near...

    That was then and I couldn't find anything near that price recently. Maybe he will get lucky but the prices I mentioned was what I had found when looking recently. I couldn't find anything decent...
  4. Replies
    10
    Views
    161

    I found one on eBay but that is always hit or...

    I found one on eBay but that is always hit or miss of course. Besides that maybe the classifieds here. I can say you will pay roughly 200 to 300 for a good used housing unless you get very lucky.
  5. Replies
    5
    Views
    141

    How much gas is in the tank?

    How much gas is in the tank?
  6. Replies
    10
    Views
    161

    Yes, the pump should have come out with the...

    Yes, the pump should have come out with the impeller inside of it. It appears the impeller is stuck on the drive shaft splines. It could be rusted on. Spray it with some PB Blaster and hopefully you...
  7. You lost me on this one. :-k

    You lost me on this one. :-k
  8. I was going to buy your carbs and pump but I...

    I was going to buy your carbs and pump but I honestly don't think there is anything wrong with mine. Also, I didn't order the pump until after you told me someone was gonna buy your carbs for $250. ...
  9. If my problem goes away, which I hope it does,...

    If my problem goes away, which I hope it does, then I will assume the problem was either the fuel pump or crank seals. I haven't found any signs of anything else being wrong. Basically if my problem...
  10. I spoke with PWC Engines today. My crank is done...

    I spoke with PWC Engines today. My crank is done and they are shipping it back to me today. They said there was basically nothing wrong with it besides some pitting. It is possible it had gotten wet...
  11. I decided to just buy a tube of Three Bond 1184....

    I decided to just buy a tube of Three Bond 1184. That is what PWC Engines recommended.
  12. What is the proper sealant for the crank case of a 1200 STX-R?

    I sent my crank out to be rebuilt. I should be getting it back next week. I started to do research about what to use to seal the case. That got me down the rabbit hole of the different types of...
  13. OP if this what you need send me a PM. Just pay...

    OP if this what you need send me a PM. Just pay shipping and I'll "pass it on".
    452353
    452354
  14. There are 5 lines coming off of the pump of a...

    There are 5 lines coming off of the pump of a 150/1200 oil pump. Each one is designed to flow a different amount of oil to each output. The outer carbs use some oil from the crank case for example....
  15. I will happily pass it on if that is what the OP...

    I will happily pass it on if that is what the OP needs. I'll post a pic of what kartracer gave me when I get home. If you need it just pay me shipping and I'll ship it out. Kartracer has been very...
  16. Make sure you connect the oil lines properly....

    Make sure you connect the oil lines properly. Follow the service manual. It is very important each output of the oil pump goes to the right carb and engine case.

    Tygon from the oil tank to the...
  17. I bought the reman fuel pump from Jet Ski...

    I bought the reman fuel pump from Jet Ski Solutions. They offered to bead blast and clear coat the cover from my pump for free. Then I can swap the pump covers so the fuel nipples will be right. That...
  18. Looking at the photos of my fuel pump does anyone...

    Looking at the photos of my fuel pump does anyone think that could be my problem? I can't imagine the pump was working 100% with all the corrosion around the gasket edges. That would explain why I...
  19. I am going to replace the pump with either a used...

    I am going to replace the pump with either a used one from turboman or a refurb one from jetskisolutions.com. I found an old thread that they use to sell parts for these pumps so I emailed them. They...
  20. I decided to take the fuel pump apart. It has a...

    I decided to take the fuel pump apart. It has a ton of corrosion on the outside of the diaphragms but the inside of both sides looks ok. The diaphragms don't appear to be damaged but the corrosion is...
  21. I had taken the fuel selector valve off to verify...

    I had taken the fuel selector valve off to verify it was working properly. It was working properly so I reinstalled it today. I then used a manual transfer pump to pump fuel out when set to on and...
  22. I checked them all again today. They are all...

    I checked them all again today. They are all popping off around 18.5 to 19.5 psi. I don't know how accurate this gauge is but I assume that is good. Should I try to adjust them or is that close...
  23. Not a bad deal!

    Not a bad deal!
  24. Double post

    Double post
  25. I got the needle seat orings in so I put them...

    I got the needle seat orings in so I put them back together tonight. I also put together a cheap pop off regulator set up to test them.
    452185
    452186
    I only have two hands so I couldn't hold the...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4