Search

Type: Posts; User: Pacer

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: 1200 to a 1500

    by Pacer
    Replies
    41
    Views
    895

    View Post

    I donít use a ring compressor to set Kawasaki cylinders. I put 2 951 cylinder studs in the corners to hold the cylinders. Put the middle pistons up and work those in first, then the outer two. ...
  2. Thread: My 1st ski!

    by Pacer
    Replies
    6
    Views
    287

    You mean the best forum on the net period.

    You mean the best forum on the net period.
  3. Replies
    4
    Views
    176

    Did you install a new fuel selector valve or...

    Did you install a new fuel selector valve or clean the old one? If you didnít install a new one, then I bet thatís your problem. Donít waste time trying to clean it better, just order an...
  4. Replies
    10
    Views
    697

    I had a 2005 RXT do the exact same thing. Fuel...

    I had a 2005 RXT do the exact same thing. Fuel pump would kick on for a split second and the tops would click. Had to disconnect the battery to stop it. It was a bad ECU.
  5. Thread: 1200 to a 1500

    by Pacer
    Replies
    41
    Views
    895

    How many hours were on the ski when it failed?

    How many hours were on the ski when it failed?
  6. Replies
    2
    Views
    302

    Are you just looking for the silicone coupler...

    Are you just looking for the silicone coupler between the water box and exhaust pipe? Search eBay for silicone coupler. Should be able to find anything you need.
  7. Thread: 951 bottom end

    by Pacer
    Replies
    1
    Views
    111

    WTB - Parts I have a used crank and good cases. PM me.

    I have a used crank and good cases. PM me.
  8. View Post

    It says ďBoost or chargeĒ?? I thought It was just boost. Which model was that warning on?
  9. Replies
    11
    Views
    989

    FS - Parts Not allowing a user to send PMs until a certain...

    Not allowing a user to send PMs until a certain post count is reached would make it harder for them. The pm scams Ive been sent were from users with 0 post count.
  10. Replies
    15
    Views
    858

    View Post

    You donít have to pull the motor to pull the head. You can time it in the hull. Pull it if the cylinders come off though.
  11. Thread: Wtb 05 rxt ecu

    by Pacer
    Replies
    0
    Views
    124

    WTB - Parts Wtb 05 rxt ecu

    Let me know if anyone out there has one.
  12. View Post

    Itís a bad coil pack. The thing that plugs into the spark plug. Pull them out one at a time and try to start . Likely two that you pull out will make it miss, or not run at all. Those 2 are good....
  13. Thread: Sunk 2012 gti

    by Pacer
    Replies
    17
    Views
    738

    Did you drain the intake manifold? Assuming you...

    Did you drain the intake manifold? Assuming you did if you pulled the motor to change the oil pumps. Why did you change the ECU? Does it rev ok out of the water?
  14. Replies
    19
    Views
    754

    I wonder why the first bearing spun!!!!????? ...

    I wonder why the first bearing spun!!!!????? Best video of the day. Thanks for posting!!
  15. On the older models, you unbolting it from the...

    On the older models, you unbolting it from the outside of the hull, the. Pry it off. Not sure if itís the same procedure for the newer style IBR.
  16. The PTO coupler is threaded onto a stub shaft...

    The PTO coupler is threaded onto a stub shaft that is threaded onto the crankshaft. Itís possible that the mechanic grabbed the pto coupler with pliers, or a big pry bar and loosened one of these. ...
  17. Ok ok... $750. But you gotta meet me on I-10.

    Ok ok... $750. But you gotta meet me on I-10.
  18. Snapped the crankshaft? How did that happen? ...

    Snapped the crankshaft? How did that happen? What else did it damage? Post some pics. Iíve never seen that on a 15f!!!
  19. Replies
    3
    Views
    702

    You can use the 07. Or you can buy just the pump...

    You can use the 07. Or you can buy just the pump on eBay for 20 or 30 bucks and it will work also. No need to buy an expensive OEM sender. Just replace the pump.
  20. $600!! Find an independent shop or do the work...

    $600!!

    Find an independent shop or do the work yourself. They canít know that the supercharger is bad if they didnít pull it, or at least pull the intake off and look at it.

    You can buy an...
  21. Replies
    5
    Views
    257

    How long does it take BUDS to do this? Is it a...

    How long does it take BUDS to do this? Is it a 30 second process, or 30 minutes? Wondering how much hassle the dealership will give me if I ask them to do it while I wait. Or if they will want me...
  22. Replies
    5
    Views
    257

    From the Manual

    From the Manual
  23. Replies
    5
    Views
    257

    New IBR actuator calibration?

    I'm installing a new IBR actuator on a 2015 GTI. The old one moves, but throws fault codes, and locks up. The manual says that a new IBR actuator will need to be calibrated by connecting BUDS and...
  24. Thread: I sunk my 260 IS

    by Pacer
    Replies
    15
    Views
    567

    As already stated. You need to pull the Intake...

    As already stated. You need to pull the Intake manifold to dump the water out.
  25. Replies
    112
    Views
    3,142

    Last time I pulled a flywheel and found that kind...

    Last time I pulled a flywheel and found that kind of damage, the mag bearing on the crankshaft had went out and caused the flywheel to hit the stator.

    Hate to see you change the flywheel and...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4