Search

Type: Posts; User: SplishSplash

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Not sure if it's the camera angle in the cylinder...

    Not sure if it's the camera angle in the cylinder pics or not, but pic 1 and 2 seem to have the oil squirter partly or totally blocked, #3 is clear.
    Not that it caused the failure, just an...
  2. Well, are you 100% sure your oil pressure is ok? ...

    Well, are you 100% sure your oil pressure is ok? Have you checked to see if the oil filter has collasped?
    How may hrs on the engine?
    Where is the oil level at?
  3. Replies
    8
    Views
    160

    Check your fuses in the MPEM Check the new...

    Check your fuses in the MPEM
    Check the new battery voltage when you press start, new batteries can be bad.
    Check all your grounds, especially the 3 on the front of the engine
    Remove the spark...
  4. The throttle cable only needs a little slack at...

    The throttle cable only needs a little slack at idle, there is no nut to worry about. The throttle stop is the thing you never should touch, as that would require a recalibration.
  5. Bran new, don't even mess with them, straight...

    Bran new, don't even mess with them, straight back to dealer as this is a warranty issue. But do let us know what the dealer found.
  6. Replies
    28
    Views
    813

    Does look well done. Whats the button and LED...

    Does look well done.
    Whats the button and LED for?
    Can you ask the previous owner if the valves and flywheel bolts were ever done?
    The supercharger intake is just a short velocity stack? or is...
  7. Replies
    12
    Views
    174

    Did you clean the main filter under the fuel...

    Did you clean the main filter under the fuel inlet needle and seat? in the carb? There is a mesh screen there that can plug up. Sounds like it starving for gas.
    Part # 49019...
  8. Thats a compression test, you need to pressure...

    Thats a compression test, you need to pressure test the closed loop cooling system and see where the coolant is getting in.
    Is the oil good or is it getting milky?
  9. Well time to pressure test the closed loop...

    Well time to pressure test the closed loop cooling system and see where the coolant is getting in.
    New head gasket right?
    Coolant bottle drops when running?
  10. Replies
    11
    Views
    382

    That is the screw you DO NOT Touch, if you have...

    That is the screw you DO NOT Touch, if you have then i think you have to reset the ECU to know its been changed.
  11. If your going for that much, you better monitor...

    If your going for that much, you better monitor your AFR's for sure as you could destroy the engine is one WOT pass if the AFR's are off. As well as everthing everyone else mentioned
  12. Replies
    15
    Views
    452

    Did you replace it with the new style filter? ...

    Did you replace it with the new style filter? (less susseotable to water in oil collaspe)If the old one collasped, I would check the new one if its the old paper style now for the same problem...
  13. Replies
    11
    Views
    382

    Adjustment is done with the little nut and the...

    Adjustment is done with the little nut and the plastic barrel on the cable. The big nuts are just mounts.
    Loosen the little nut and then rotate the barrel untill your throttle rests on the stop and...
  14. Replies
    2
    Views
    88

    Well are you sure it needs an impeller? Could be...

    Well are you sure it needs an impeller? Could be just the wear ring.
    Super charged or not? If supercharged, you should replace the exhaust valves as they tend to snap.
  15. Replies
    9
    Views
    299

    Boost leak, leaking intercooler, slipping SC...

    Boost leak, leaking intercooler, slipping SC clutch are the starting points after fresh plugs.
  16. Replies
    11
    Views
    382

    is there a bit of slack in the throttle cable at...

    is there a bit of slack in the throttle cable at the TB? If it too tight the engine cannot find idle and will run poorly. Check and be sure its against the throttle stop when the lever is released....
  17. They should be paying you to haul that crap away,...

    They should be paying you to haul that crap away, its worth nothing. Looks like it had a fire and was striiped of anything of value.
    Walk away, no run away!
  18. You need a set of spark plug wires too! Also,...

    You need a set of spark plug wires too! Also, your missing the oil catch tube on the air intake, Picture #1 of the engine, on the in take there is a nipple pointing down and the tube should be on...
  19. Replies
    3
    Views
    141

    Your gauge may be off a bit, (very common) what...

    Your gauge may be off a bit, (very common) what you want is consistancy and good reading across them, thats more important.
    Your fine, enjoy.
  20. Also, wasn't there a thread or notice about the...

    Also, wasn't there a thread or notice about the wiring harness touching the block on a sharp corner that cn cause this kind of issue?
    Hard riding moves the engine around and harness around and it...
  21. Replies
    10
    Views
    494

    Well using simple math and not taking into...

    Well using simple math and not taking into account slippage. the answer no

    See 22 is the number of inches a prop would move in 1 rpm based on pitch and 20 is for the other one, so math says...
  22. Well, it looks like it got very hot too, really...

    Well, it looks like it got very hot too, really discoloured.
    Thats not a crack in the crank in pic 2? Just a casting mark?
    Looks like oil starvation, one from the toasted bearing and two the...
  23. Replies
    27
    Views
    1,665

    Fastest ski on the water? Depends, what type of...

    Fastest ski on the water? Depends, what type of water your talking about riding in. Glass,chop, open water . Different skis shine in differnt conditions..
  24. Aluminum shards, probably spun a crank bearing or...

    Aluminum shards, probably spun a crank bearing or the thrust washers are gone and its eating into the aluminum. Did you check the crank for back and forth play?
    Your going to have to split the...
  25. Replies
    18
    Views
    390

    Are you sure its back fireing? Things to...

    Are you sure its back fireing?
    Things to check, compression and cam timing. Maybe the cam slipped Pin the crank and see if the cam lines up.

    If its sputtering, and not backfiring, have your...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4