Search

Type: Posts; User: FL_Rider

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    26
    Views
    976

    Thanks fellas for the info on the cameras. I have...

    Thanks fellas for the info on the cameras. I have a harbor freight one and its pretty low resolution.
  2. Replies
    26
    Views
    976

    Those are some pretty clear pics. Were those...

    Those are some pretty clear pics. Were those taken with the inspection camera recommended by nmpeter?
  3. I replaced the whole crankshaft. It was a rebuilt...

    I replaced the whole crankshaft. It was a rebuilt one, and was under warranty.
    If you can't find out what is causing the noise and you want to check to see if its the labyrinth, you can just pull...
  4. I knew you guys would want to know, but I don't...

    I knew you guys would want to know, but I don't want to bash them. They did honor the warranty, and I understand people including myself make mistakes.
  5. I can say it definitely was an experience...

    I can say it definitely was an experience troubleshooting mine. In case the topic of this thread doesn't turn out to be what happened to my ultra, I started a new thread about mine titled Ultra 150...
  6. Ultra 150 defective labyrinth seal and crank rebuild

    I thought I'd start a new thread on this one since this should be documented.

    I got a rebuilt crank for my ultra 150 and I didn't measure the OD of the labyrinth seals and main bearings prior to...
  7. I recently had something similar happen to my...

    I recently had something similar happen to my ultra. I rebuilt the engine last fall and put approx 20 hours on it with no problems. Around March I take it out after it sat for a couple months. I hear...
  8. 5 PSI should be enough. The sea doo manual says...

    5 PSI should be enough. The sea doo manual says 5, the kawasaki manual doesn't say at all. Why take a chance on distorting or splitting a seam on your tank?

    Edit: I just looked in the sea doo...
  9. Well, I'm glad to hear you found the problem...

    Well, I'm glad to hear you found the problem before it caused engine damage. On the bright side, some new line is cheaper than a selector valve. I have regular old automotive fuel line in my Sea Doo...
  10. Replies
    14
    Views
    848

    Wow! Excellent design and work.

    Wow! Excellent design and work.
  11. [QUOTE=beekermartin;3047061]I just got back from...

    [QUOTE=beekermartin;3047061]I just got back from the water. It seems to be running great but I definitely have an issue with the fuel system. The fuel light came on so I switched to the reserve. It...
  12. It depends on what you're going to use it for. ...

    It depends on what you're going to use it for.
    I prefer the Ultra 150 because of what I use it for, which is mostly single riding with an occasional passenger. The places I ride are mostly rivers...
  13. I just did a mock up of getting a screwdriver on...

    I just did a mock up of getting a screwdriver on the adjustment screws. Of course, it will be a little tougher working in the hull, but I think its do-able. Since pulling the carbs would waste...
  14. Replies
    11
    Views
    393

    I got the Keihin o-rings from newmotorcycleparts...

    I got the Keihin o-rings from newmotorcycleparts dot net.
    Part OR-4619 is the 2.8 mm x 1.2 mm
    Part OR-4623 is the 6.9 mm x 1.3 mm
    They are Buna NBR.

    I got the 6.5 mm x 1.5 mm o-rings from...
  15. Replies
    11
    Views
    393

    Thanks for the info on the stacked o-rings. I was...

    Thanks for the info on the stacked o-rings. I was thinking about getting square rings and stacking them but I didn't know if it would work. I could find square rings, but the height and width were...
  16. Replies
    11
    Views
    393

    So, I'll add a little more to this thread......

    So, I'll add a little more to this thread... Since using the 6.9 x 1.3 o-ring on an OEM needle/seat, which worked well, I decided to try a needle & seat from SBT. At the time, the SBT needle/seat...
  17. Replies
    12
    Views
    433

    That's exactly how you do it. You don't need to...

    That's exactly how you do it. You don't need to really fab a pointer though, just put a piece of tape on the engine next to the pto and draw a line on it that lines up with the mark on the pto for...
  18. The mixture screw o-ring is different from the...

    The mixture screw o-ring is different from the needle/seat o-ring. I ordered some different size Keihin o-rings and the 2.8 mm ID x 1.2 mm cross section fit the best on the mixture screw. I did a...
  19. Cool... Keep us posted

    Cool... Keep us posted
  20. I would wait until its broken in and your plugs...

    I would wait until its broken in and your plugs are looking good. You said you swapped plugs 2 and 3? So, the brown color came from it being in cylinder 3? Maybe put a fresh plug in #2 and ride it a...
  21. If that's the case, that would be an indicator...

    If that's the case, that would be an indicator that the lean condition is only in the low speed circuit. There are some threads on Greenhulk about carb tuning that are some real informative reading....
  22. Is the slight hesitation only when you punch it...

    Is the slight hesitation only when you punch it off idle? Or does it also do it if you're going steady at about 1/3 - 1/2 throttle and then punch it?
  23. I have a theory on the pissers. Since the exhaust...

    I have a theory on the pissers. Since the exhaust builds pressure when you rev it, that pressure creates back pressure on the cooling system because the cooling system is routed into the exhaust...
  24. There is a low speed adjuster for each carb....

    There is a low speed adjuster for each carb. There are no high speed adjusters.

    I only posted close up shots of two of the carbs instead of all three carbs. I didn't mean to imply there were only...
  25. If you do decide to do it, the mixture screw has...

    If you do decide to do it, the mixture screw has a spring, a tiny washer, and an o-ring on it. The washer and o-ring will likely stay in the hole and you'll have to make a tiny hook out of a paper...
Results 1 to 25 of 94
Page 1 of 4 1 2 3 4