Search

Type: Posts; User: dtnSUV1200

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    489

    It's always a good idea to trace it from the tank...

    It's always a good idea to trace it from the tank to the carbs to make sure fuel is flowing freely to the carbs. The alarm on these old skis are mounted on the rear exhaust taking the temperature of...
  2. I run premix. I put 32:1 for the break-in,...

    I run premix. I put 32:1 for the break-in, probably off by some ounces. Everything seemed to be fine. Compressions are good. I'm on the second tank now, 40:1 mix. I will remember 25:1 on the next...
  3. Replies
    3
    Views
    489

    Do a compression test first. If compressions are...

    Do a compression test first. If compressions are good, then check fuel line, fuel filter, fuel line check valve, if everything is good then rebuild the carbs. As for the hot pisser, if you don't get...
  4. I put moister remover/fuel stabilizer in the...

    I put moister remover/fuel stabilizer in the first tank.
  5. I just rebuilt mine with it. If you still haven't...

    I just rebuilt mine with it. If you still haven't gotten it from Hammer, shoot me a PM. I got mine copy from Teme!
  6. SUV1200 Spark plugs after rebuilt, first tank!

    Hey guys! I'd like to thank guys for helping me with the rebuilt. It was my first too. There was a lot of research, and knowledge gained from it.

    These spark plugs are about 4 hours after the...
  7. Replies
    0
    Views
    264

    Stator cover getting hot

    I finally got my ski put back together and fired up for the first time. It idles fine, but rev seems to be hanging a bit before returning to idle. Also the stator cover is hot but I can still touch...
  8. Replies
    20
    Views
    1,476

    I know the oil lines didn't fall off, carbs are...

    I know the oil lines didn't fall off, carbs are good. The High and Low adjustment screws were 2 turns out. The thing was running rich. I also see dark liquid at the bottom of the crankcase under the...
  9. Replies
    20
    Views
    1,476

    I opened the middle carb today. I am left with...

    I opened the middle carb today. I am left with more questions than answers. The carb looked cleaned. Nothing was wrong as far as I can see. I have uploaded all the of the pictures. Can you guys see...
  10. Replies
    20
    Views
    1,476

    you mean the fuel pump diaphragm or the fuel pump...

    you mean the fuel pump diaphragm or the fuel pump side? i think it maybe running rich. the spark plugs are dark. i'll take some pics soon.
  11. Replies
    8
    Views
    1,213

    Just bought the 1999 gp1200 block...

    Just bought the 1999 gp1200 block non-power-valve. From my research, it is the same as my 2002 suv1200 65u non-power-valve but I would like to confirm it with you guys.
  12. Replies
    20
    Views
    1,476

    I just got to the carbs today. The oil lines are...

    I just got to the carbs today. The oil lines are really tight. I had to cut the lips open to pull them. The carbs 6 nuts were not that tight. The gasket seal around the middle card was kind of loose....
  13. Replies
    8
    Views
    1,213

    Thanks for that info. I thought they came just...

    Thanks for that info. I thought they came just like specs and ready to install.
  14. Replies
    8
    Views
    1,213

    Cylinder sleeve removal?

    For some reason, none of the shops around tampa bay wants to bore out my block and SBT wants my block plus $700 to exchange for theirs, too much for me. I see the the block is sleeved and new sleeve...
  15. Replies
    2
    Views
    489

    Thanks ncdoo. I see the cylinders are sleeved....

    Thanks ncdoo. I see the cylinders are sleeved. How hard is it to remove the sleeve and put in a new one? My concern is I may crack the block pounding it.
  16. Replies
    5
    Views
    627

    Thanks alot guys! I just got a copy of it!

    Thanks alot guys! I just got a copy of it!
  17. Replies
    5
    Views
    627

    Yamaha SUV 1200 shop manual.

    Does anyone the manual with all the torque specs on the nuts and bolts online? I searched manualslib.com but they only have owners manual.
  18. Replies
    2
    Views
    489

    Yamaha suv 1200 OEM piston size

    I may have to bore my cylinder head. I am not familiar with the piston sizing. I see .84mm and +5 over. I don't understand. I would like to know the oem piston size and what would be the next sizes...
  19. Replies
    20
    Views
    1,476

    i will look at that once i get the everything...

    i will look at that once i get the everything off. thanks guys!
  20. Replies
    20
    Views
    1,476

    I use the boat style primer bulb. installed in...

    I use the boat style primer bulb. installed in the fuel supply line.
  21. Replies
    20
    Views
    1,476

    Any idea on how this could happen?

    Any idea on how this could happen?
  22. Replies
    20
    Views
    1,476

    Can the sleeve be machined or re-sleeved or honed...

    Can the sleeve be machined or re-sleeved or honed out. I saw a junk is melted on the cylinder wall.
  23. Replies
    20
    Views
    1,476

    Hi guys, I was able to take it today. The...

    Hi guys, I was able to take it today. The cylinder wall is scorned. The piston ring maybe gone. Can it still be fixed? What can i do with the middle cylinder wall. Please advise. Thanks.

    here are...
  24. Replies
    20
    Views
    1,476

    No compression in middle cylinder

    I have a 2002 yamaha suv with around 100hours on it. I recently installed a primer bulb on the fuel supply line to help pressurize the tank and prime the carbs. It worked great for about 1 hour. The...
  25. Replies
    7
    Views
    908

    The carbs are good. I only have time to run it...

    The carbs are good. I only have time to run it once or twice a month. it takes a long time to get fuel to the carbs after a long layoff. i don't want to kill the starter and battery.
Results 1 to 25 of 26
Page 1 of 2 1 2