Search

Type: Posts; User: Jhb

Page 1 of 4 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    17
    Views
    856

    Not familiar with the 2020 but a couple of must...

    Not familiar with the 2020 but a couple of must haves in my opinion is ribbon delete, & bov
  2. Innovate for the wideband/afr, I have one works...

    Innovate for the wideband/afr, I have one works great easy to install, seems to be a popular choice.
  3. Replies
    14
    Views
    599

    I don't know if it matters or not, but I went...

    I don't know if it matters or not, but I went back over the Riva instructions on setting the fuel pressure it says to un-hook the rising rate hose from regulator, then to pinch off or block the rest...
  4. Replies
    14
    Views
    599

    Yea I was pleased with everything but the rich...

    Yea I was pleased with everything but the rich AFRs, I am running r&d plate with 2 shims on each side, so I feel like I could get some more speed out of it, just got to figure out this rich problem....
  5. Replies
    14
    Views
    599

    I'll have to give that a try, but what would...

    I'll have to give that a try, but what would cause it to do that?.. does the rising rate need its own dedicated line? Mine is hooked in with boost gauge.
  6. Replies
    14
    Views
    599

    Went out to lake today to check the AFRs after...

    Went out to lake today to check the AFRs after installing rrfr. The ski ran pretty decent, but I am pretty confused about the AFRs I was getting. I set regulator on 40psi with rising rate hose...
  7. Replies
    14
    Views
    599

    Ok thanks waiting on my boost gauge to come in...

    Ok thanks waiting on my boost gauge to come in then gonna head to lake and see what happens.
  8. Replies
    14
    Views
    599

    Thanks Tommy, that makes me feel better. So...

    Thanks Tommy, that makes me feel better. So cruising around at normal rpms 4-6k it's ok to be 13-14ish on afrs?
  9. Replies
    14
    Views
    599

    I done it mainly just out of curiosity, I haven't...

    I done it mainly just out of curiosity, I haven't had any issues, just playing it safe, can ride with more piece of mind, my rpms at wot usually 8640.
  10. Replies
    14
    Views
    599

    RRFR / AFR TUNNING (stage 2 sho)

    This is my first time, if someone could help shed a lil light on this for me I would appreciate it. I just recently installed innovate wide band, and put in a Riva rrfr today. All my testing today...
  11. 8 years later, any update??? I hate when u...

    8 years later, any update???

    I hate when u read a post like this with so much info and then just leaves you in the dark like this, wondering all day what is was!!
  12. Replies
    6
    Views
    253

    WTB Yes that works for me, about to order one up,...

    Yes that works for me, about to order one up, wish I would have found this first cause I done spent $20 on taps
  13. Replies
    6
    Views
    253

    WTB Well son of a gun, I been searching my butt off...

    Well son of a gun, I been searching my butt off never seen that... Thank you sir!!
  14. Replies
    6
    Views
    253

    WTB I did and screwed it up

    I did and screwed it up
  15. Replies
    6
    Views
    253

    WTB WTB: 2009-2012 fz sho O2 sensor adapter

    Need a adapter for a O2 sensor to go into factory 32mm bung hole. I looked the world wide web over and can't find one.
    Thanks
  16. Replies
    16
    Views
    842

    Very good advise sir, I found it with mirror was...

    Very good advise sir, I found it with mirror was able to guide it to the opening with some wire,and eased it out with a magnet!!459850459851
  17. Replies
    32
    Views
    1,660

    Here is my factory O2 plug drilled out with bung...

    Here is my factory O2 plug drilled out with bung extender and then 02 sensor.. Would this be too high above and out of the exhaust stream to get accurate readings??
    Without the bung extender the 02...
  18. Replies
    16
    Views
    842

    I will look again with mirror before I put it...

    I will look again with mirror before I put it back together, I have to wait for new one to come in anyway.
  19. Replies
    16
    Views
    842

    Had same thing happened today, doing 100hr...

    Had same thing happened today, doing 100hr service on my wife's fresh water only ski, pulled exhaust to check filter and it was completely gone! Ski runs great too. I shook water box around and...
  20. Replies
    26
    Views
    2,368

    I have a fizzle thats a few years old, one of my...

    I have a fizzle thats a few years old, one of my rubber couplings needed replacing, I contacted Mr. Fizzle here on this forum, he then sent me ALL new couplers, free of charge, from a new and...
  21. Replies
    32
    Views
    1,660

    What diameter is the heat sink threads 18mm?

    What diameter is the heat sink threads 18mm?
  22. Replies
    32
    Views
    1,660

    Yes I can see how the heat sink would definitely...

    Yes I can see how the heat sink would definitely help!.. I already have a extended bung that should put the sensor just about at the top of the exhaust, it would not be down directly in center of...
  23. Replies
    32
    Views
    1,660

    I am working on this same thing right now! ...

    I am working on this same thing right now!

    What about the bung extender, where u would maybe be taking the senor out of the direct exhaust stream? Will doing this mess up the afr readings or does...
  24. Replies
    34
    Views
    1,560

    X

    X
  25. Replies
    71
    Views
    8,899

    FS Probably going electrical, got a plan I think of...

    Probably going electrical, got a plan I think of how to keep from getting wet, gonna be a few weeks before I can fool with it, I will share if it works out.
Results 1 to 25 of 85
Page 1 of 4 1 2 3 4