Search

Type: Posts; User: Doug78

Page 1 of 8 1 2 3 4

Search: Search took 4.04 seconds.

  1. Replies
    6
    Views
    310

    That was my thought...its not a seadoo where this...

    That was my thought...its not a seadoo where this is a serious concern.
  2. Replies
    31
    Views
    720

    Glad to hear youve been running them without...

    Glad to hear youve been running them without issue, i knew i was being a bit paranoid about the pressures.

    Looking for them now. amazon wants 54 bucks...Found another source that sells them for 4...
  3. Replies
    31
    Views
    720

    THe first antelco valve i found was rated for...

    THe first antelco valve i found was rated for 300kpa (43 PSI). Is that enough? I dont recall what pump pressure is but do remember it be higher than i thought.
  4. Replies
    27
    Views
    756

    Its not hard, but it is awkward. I had one...

    Its not hard, but it is awkward. I had one leaking a while ago and resealed both.

    Pulled the rear seat bracket to get better access, cleaned old glue and 5200'd the insert back in. Bolted up...
  5. Replies
    71
    Views
    8,899

    FS Where you able to find a liquid filled gauge that...

    Where you able to find a liquid filled gauge that is 2 1/16"?? I got a 2 5/8 and couldnt find a smaller one.
  6. Replies
    56
    Views
    5,662

    I'm on the casting flaw train. I ride I the same...

    I'm on the casting flaw train. I ride I the same area as speeder and have had my fzr since 2009 and running 15psi boost since 2012. The only wild card is my heavily modded cooling system. I keep...
  7. Yes check plugs, I've had a some funky things...

    Yes check plugs, I've had a some funky things happen with my ski and plugs often are the culprit.
  8. Replies
    5
    Views
    496

    Should work, the bottom isnt gel coated it is...

    Should work, the bottom isnt gel coated it is painted.

    With proper prep it will stick. There is a giant long topic somewhere in here about it. Ive been debating doing mine for a while, 10 years...
  9. Replies
    17
    Views
    1,605

    Ideally yes, it's not very helpful to have the...

    Ideally yes, it's not very helpful to have the nose bobbing like all the seadoo photos I have seen...

    I can't find the official details but IIRC boats under 20 feet, with over 2hp are required to...
  10. Replies
    17
    Views
    1,605

    Where was all the foam before you gutted it? Does...

    Where was all the foam before you gutted it? Does anyone know if the yamaha float level when full of water??
  11. Replies
    7
    Views
    524

    I seem to remember putting a washer under the...

    I seem to remember putting a washer under the back 3 bolts of the seat bracket to let air out. Doesn't effect the bucket use. I don't think mine are installed anymore, just forgot to put them in one...
  12. Replies
    81
    Views
    16,044

    Shouldmfit the original shos?

    Shouldmfit the original shos?
  13. Replies
    47
    Views
    2,185

    Got an air fuel gauge?

    Got an air fuel gauge?
  14. They exist in australia http://jetfish.net/

    They exist in australia

    http://jetfish.net/
  15. Out of those choices, the Kawasaki would be best....

    Out of those choices, the Kawasaki would be best. They have insane storage capacity! Not a ski out there competes with the Kawasaki 212 liters of storage. The fish pro is 149 liters storage (not sure...
  16. Replies
    47
    Views
    2,185

    I had this experience, ran fine without the...

    I had this experience, ran fine without the seats. AFR will go really rich if you have an exhaust leak.
  17. Replies
    11
    Views
    860

    Did you charge the battery before testing??

    Did you charge the battery before testing??
  18. Replies
    12
    Views
    755

    Im going to order one in preparation for my next...

    Im going to order one in preparation for my next clutch change. Will do a comparison when I take it apart.

    No promises on when...I'm not going in there before it fails.
  19. Replies
    18
    Views
    1,393

    FS I'll take the nozzle too! Check you pms

    I'll take the nozzle too! Check you pms
  20. Replies
    18
    Views
    1,393

    FS Sorry for that ur luck, I had a similar...

    Sorry for that ur luck, I had a similar experience with C3/shaft failure. What clutches are you running? I did a 15.5 wheel with the latest clutch and idler gear and it is holding well. Expected to...
  21. Replies
    18
    Views
    1,393

    FS Keeping the machine??

    Keeping the machine??
  22. Replies
    11
    Views
    666

    It should spin really easy, you will need a new...

    It should spin really easy, you will need a new clutch. When they fail they can start to lock up sometimes.

    The little bit of play is normal, just room for the oil film. I remember the first time...
  23. Replies
    7
    Views
    1,070

    Sleeves can be bored, no nikasil. Mine is .020...

    Sleeves can be bored, no nikasil. Mine is .020 over and been fine. Unless something changed with the SVho blocks...but I don't think so.

    Aftermarket buckets are thicker and may require Grinding...
  24. Disregard my comments, totally thought you said...

    Disregard my comments, totally thought you said clutch only span one way.

    You need a clutch...simple.
  25. Replies
    40
    Views
    4,349

    They need.to go.back in where they came from. The...

    They need.to go.back in where they came from. The shims set the valve lash. If you swap everything around then the lash should be checked adjusted.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4