Search

Type: Posts; User: bainer1290

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds; generated 23 minute(s) ago.

  1. Replies
    102
    Views
    7,099

    Thanks!!

    Thanks!!
  2. Replies
    102
    Views
    7,099

    Started the engine today, it fired right up as I...

    Started the engine today, it fired right up as I primed the fuel lines and was able to use the primer. Now the weather just needs to warm up so I can take it for a test drive!!
  3. Replies
    102
    Views
    7,099

    Looking good!!

    Looking good!!
  4. Replies
    102
    Views
    7,099

    Finally got all the parts needed for the carb...

    Finally got all the parts needed for the carb rebuild, was waiting on the Mikuni kits, rejetted as per Bills specs 125 mains, 110 pilots, 1.5 N&S and 9g springs. Tested popoff for all 3 is in the...
  5. Replies
    0
    Views
    127

    WTB - Parts GP1200R Riva F/A Watersocks

    Anyone get a spare pair of watersocks / filter socks they want to sell?

    Thanks

    http://greenhulk.net/forums/attachment.php?attachmentid=472670&stc=1
  6. Replies
    102
    Views
    7,099

    Cool I used to have a 99GP1200 about 10 years ago...

    Cool I used to have a 99GP1200 about 10 years ago so looking forward to getting back into it. We go to BC and Montana lots well that was before covid but hopefully by next year that will be an option...
  7. Replies
    102
    Views
    7,099

    That makes sense more pressure in a triple. ...

    That makes sense more pressure in a triple.



    Thanks! I am in Lethbridge, the ski was from Med Hat but not sure on the history as it was in pieces when I found it... Should have it back on the...
  8. Replies
    102
    Views
    7,099

    Thanks Jonesfxr, that makes sense, I suspect my...

    Thanks Jonesfxr, that makes sense, I suspect my threebond on the seals would help some with that as well.
  9. Replies
    102
    Views
    7,099

    I did put threebond around the outer seal lips as...

    I did put threebond around the outer seal lips as I wanted to make sure they were sealed tight. What does the rest of this article show?
  10. Replies
    102
    Views
    7,099

    I don't think I have seen this before, whats the...

    I don't think I have seen this before, whats the full write up say?
  11. Replies
    102
    Views
    7,099

    Well good news the engine is now tight! Held 6psi...

    Well good news the engine is now tight! Held 6psi with no loss for 6 minutes, after 30 mins it was at 5.6psi, then at an hour 5.25psi.

    Next up a compression test then I will be dropping it back...
  12. Replies
    102
    Views
    7,099

    Thats good to know, I have no experience with the...

    Thats good to know, I have no experience with the copper spray.
  13. Replies
    102
    Views
    7,099

    Appreciate the advice! I tore it down and hit the...

    Appreciate the advice! I tore it down and hit the base gaskets and pv covers with 3bond. Hoping the next pressure test will be tight.
  14. Replies
    102
    Views
    7,099

    Question on pressure testing as I want to...

    Question on pressure testing as I want to clarify.

    I read the sticky http://greenhulk.net/forums/showthread.php?t=9408
    and the Group K article https://www.groupk.com/airleak.html

    One says the...
  15. Replies
    102
    Views
    7,099

    Engine assembly complete, pressured tested good...

    Engine assembly complete, pressured tested good to go!

    Next need to rebuild the carbs and then its time to drop the engine back in the hull.
    ...
  16. Replies
    102
    Views
    7,099

    Got the motor partly built over the past few...

    Got the motor partly built over the past few weekends. Its coming together good so far!...
  17. Replies
    102
    Views
    7,099

    Sounds great, I know what you mean about the...

    Sounds great, I know what you mean about the waterbox and hose routing in the rear its tight back there lol
  18. Replies
    102
    Views
    7,099

    Ok so I would have 4 pissers? The stock ones from...

    Ok so I would have 4 pissers? The stock ones from the pipe under the rub rail on the port and starboard sides. Then I will add 2 on the rear for the 2nd and 3rd cylinders?



    I added a 3/8 thru...
  19. Replies
    102
    Views
    7,099

    What's the best cooling setup for a stage 2...

    What's the best cooling setup for a stage 2 modified GPR with the holeshot kit installed?

    As I will be using Riva heads I have 3 outlets on the heads along with the stock single pipe with 2 inlets...
  20. Replies
    2
    Views
    212

    SOLD Got one, thanks again Richard!!

    Got one, thanks again Richard!!
  21. Replies
    2
    Views
    212

    SOLD SHO or Riva Steering Nozzle for GPR

    Looking for a steering / exit nozzle, let me know if you have one to sell. Thanks
  22. Replies
    102
    Views
    7,099

    Sounds good thanks!

    Sounds good thanks!
  23. Replies
    102
    Views
    7,099

    Figured out where the styrofoam goes! ...

    Figured out where the styrofoam goes!

    http://greenhulk.net/forums/attachment.php?attachmentid=470687&stc=1
  24. Replies
    102
    Views
    7,099

    I need to see a pic of where that ? Styrofoam...

    I need to see a pic of where that ? Styrofoam piece fits then, it has to fit somewhere.

    http://greenhulk.net/forums/attachment.php?attachmentid=470606&stc=1
  25. Replies
    102
    Views
    7,099

    Yes I am planning to do the Oside recipe 125...

    Yes I am planning to do the Oside recipe 125 mains, 110 pilots, 1.5 Needle and Seat, 95 gram spring. I was planning to disable the Accelerator Pump, Drilled Return Pressure Balancing Mod with a jet...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4