Search

Search: Search took 1.00 seconds.

  1. Replies
    62
    Views
    2,964

    If you think being towed behind a 1 foot wake, is...

    If you think being towed behind a 1 foot wake, is riding knock yourself out bro. Tell you what ride behind a pro-tow boat either a Corect Craft, Super Air Nautique, Malibu or Tige. Then tell me that,...
  2. Running Seadoo out of the water with no hose, received exhaust temperature warning

    All jokes aside Roman the best way to cool the exhaust is on the hose. This is how I do it when flushing. Hook up your hose and start the engine. Turn on the water and Run it for a couple mins to get...
  3. Replies
    185
    Views
    15,547

    Haters gonna hate and truth is always buried by...

    Haters gonna hate and truth is always buried by the hands of haters.

    You want to blame the Mexican production workers? Go ahead, but you are both dead wrong and perhaps too consumed by prejudice...
  4. Replies
    12
    Views
    1,411

    Just pull the pin out of the crank.

    Just pull the pin out of the crank.
  5. Replies
    33
    Views
    4,234

    haha, maybe an line heat exchanger to cool the...

    haha, maybe an line heat exchanger to cool the coolant going into the oil cooler
  6. This explains a lot.

    This explains a lot.
  7. Replies
    31
    Views
    3,865

    He still hasn't posted in this thread, only...

    He still hasn't posted in this thread, only matter of time...
  8. How To Install a GPS Speedometer Module (CanDooPro)

    Full instructions for installing a CanDooPro GPS Speedomoeter Module (part no. 9501) for 1997 to 2006 Sea-Doo models with lake temperature sensor.
    If you like our videos, please Subscribe! (a...
  9. Replies
    1
    Views
    1,006

    Antifreeze Exhaust Flush for Sea-Doo

    In this how-to video we show you how we protect our exhaust system from the threat of a freezing winter by pumping RV antifreeze through it. Performed on a Sea-Doo 2005 GTX 185 jet ski, this...
  10. Replies
    16
    Views
    2,104

    I stopped lapping valves a long time ago, mostly...

    I stopped lapping valves a long time ago, mostly because I bought a brand new guide and seat machine. After every valve job I cut, I vacuum test each pair of valves and I have noticed a tighter seal...
  11. Replies
    14
    Views
    2,330

    seadoo heads come factory 3 angle valve job. ...

    seadoo heads come factory 3 angle valve job.

    Here is what you should be doing when installing new valves, hand lapping is very "back yard"

    342980342981
  12. I don't use a tender. I store 8 machines over the...

    I don't use a tender. I store 8 machines over the winter. I remove the batteries for the winter. I fully charge them, the once every two months, I give them another full charge. Then in the spring, I...
  13. Yes, some will work but they tax the electrical...

    Yes, some will work but they tax the electrical system so badly that you don't have enough juice to charge the battery, AND the rectifier runs so hot it will burn up in a matter of hours. OEM Seadoo...
  14. Replies
    20
    Views
    2,030

    there needs to be a slight bit of the shell above...

    there needs to be a slight bit of the shell above the case to allow for "crush" this is what holds the bearing in the cases if there was no lip there would be no tension to hold the bearing firm and...
  15. Replies
    19
    Views
    3,641

    Test this, disconnect pipe going to throttle...

    Test this, disconnect pipe going to throttle body, start ski, let idle, put your hand on the throttle body as if to seal it off completely. If ski dies you have an electrical/calibration problem. If...
  16. Replies
    18
    Views
    11,793

    Re: seadoo 140mm alignment tool dimensions

    Overrated I think not but u can get it close. I personally use a alignment tool on all my skis but im trying to get all the performance out of mine that I can. Especially on the hx and xpl with 2...
Results 1 to 16 of 18