Search

Page 1 of 10 1 2 3 4

Search: Search took 1.00 seconds.

  1. Mmmm hmmmm..........sunk........just like I...

    Mmmm hmmmm..........sunk........just like I thought.
  2. Replies
    7
    Views
    283

    Not on that engine.

    Not on that engine.
  3. I'd go check it out. The lower compression in one...

    I'd go check it out. The lower compression in one cylinder doesn't bother me that bad.....I see it all the time. Betting after a short ride it comes up. It amazes me that so many people don't know...
  4. Replies
    3
    Views
    196

    Are the gauges hooked up? As soon as you crank it...

    Are the gauges hooked up? As soon as you crank it over the gauges should power up and stay on for a minute or so.
  5. Replies
    7
    Views
    294

    The impeller. I have both here I'll try to get...

    The impeller. I have both here I'll try to get you a pic.
  6. Replies
    7
    Views
    294

    No, it's how the pump shaft goes into the...

    No, it's how the pump shaft goes into the impeller.
  7. Thread: Cylinder Crack

    by Myself
    Replies
    15
    Views
    562

    When the engine gets hot that crack is expanding...

    When the engine gets hot that crack is expanding and allowing water to flow through into the port. Replace it.
  8. Thread: Yamaha FX HO

    by Myself
    Replies
    1
    Views
    173

    Well, the trailer and a few parts are worth $500....

    Well, the trailer and a few parts are worth $500. Can't lose! I just finished piecing one together on the cheap. So far, so good but we've only put 2.3 hours on it. Look in the build section for...
  9. Replies
    9
    Views
    313

    Wait a minute...........you have a 10mm wrench...

    Wait a minute...........you have a 10mm wrench you can actually find??!??
  10. Replies
    32
    Views
    3,305

    Got all the cooling and electrical hooked up...

    Got all the cooling and electrical hooked up yesterday. Also made my own free flow exhaust with a couple pvc street 90's as I found in another thread. Filled with oil, put in new plugs, and a hot...
  11. Replies
    32
    Views
    3,305

    Ok, so I figured this exhaust out. First, MAKE...

    Ok, so I figured this exhaust out. First, MAKE SURE the thermoswitch and engine temp switches are installed in the block on the exhaust side. Otherwise they are ALMOST impossible to get to.......ask...
  12. Replies
    5
    Views
    181

    Could very well be the midshaft bearings since...

    Could very well be the midshaft bearings since nobody seems to know about greasing them.
  13. Replies
    10
    Views
    660

    Yes, since I had to change it several times, and...

    Yes, since I had to change it several times, and had the cover off anyway..........
  14. Replies
    10
    Views
    660

    Next I put the tube straight down the newly...

    Next I put the tube straight down the newly drilled and tapped hole. I had to wiggle it just a bit "feeling" my way down til it stopped and my tape was about the same place as in the dipstick tube....
  15. Yes, you can leave the oil in. Tilt the trailer...

    Yes, you can leave the oil in. Tilt the trailer as much as the wheel jack will allow, little to no oil will come out. I just did this a month ago.
  16. Replies
    27
    Views
    817

    You better pop the carbs off and check the reeds.

    You better pop the carbs off and check the reeds.
  17. No, you cant swap the guts. When the key is worn...

    No, you cant swap the guts. When the key is worn out you get a new one and have it programmed.
  18. Replies
    16
    Views
    966

    Looks like water intrusion. Is that head dome a...

    Looks like water intrusion. Is that head dome a lot cleaner than the other 2?
  19. Replies
    42
    Views
    778

    Retest all stator wires while unhooked. And test...

    Retest all stator wires while unhooked. And test them to ground. And test all output voltages while cranking. As in that first post of my thread. Also make sure and ohms test each coil individually....
  20. Replies
    42
    Views
    778

    What is the trigger voltage? Whi/yel to black. ...

    What is the trigger voltage?
    Whi/yel to black.

    If it's not at least one volt the cdi will Not fire.
  21. Replies
    9
    Views
    468

    I'd be more worried about the rust on the...

    I'd be more worried about the rust on the cylinder walls and rings from being stuck from improper winterization......
  22. Replies
    8
    Views
    306

    Also, did you place the rv with front piston at...

    Also, did you place the rv with front piston at tdc?
  23. Replies
    32
    Views
    3,305

    So.....getting in the groove of running my own...

    So.....getting in the groove of running my own shop and finally trying to get some "me" time. People expect me to fix a watercraft 24/7 I guess. Now I have set hours and I don't answer the phone...
  24. Replies
    6
    Views
    235

    I have that in my notes somewhere. The stock...

    I have that in my notes somewhere. The stock airbox has several 1" holes. You just go around that same edge and drill a whole bunch more.
    I always do euro specs with stock airbox and elbow and...
  25. Replies
    19
    Views
    1,069

    I don't care who does the machine work....ALWAYS...

    I don't care who does the machine work....ALWAYS check clearance and ring end gap before installing pistons. It only takes an extra 5 minutes, not worth any potential headaches like this without...
Results 1 to 25 of 238
Page 1 of 10 1 2 3 4