Search

Type: Posts; User: GDS

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    175

    Great I found the manual and it says 20 degrees...

    Great I found the manual and it says 20 degrees so I'm dead on no adjustment needed. Thanks for your help.
  2. Replies
    3
    Views
    175

    I found lots of other stuff for this ski but just...

    I found lots of other stuff for this ski but just didn't see timing. I'll look again but with that said I checked it and it looks to be at 20. There is no pointer so i'm taking it from center of the...
  3. Replies
    3
    Views
    175

    Need help with timing on 01 Virage

    I just got my new CDI installed and the ski is running again. But I can't seem to find how to check timing nor what it should be. Now I do see a sticker that says 23 at idle but it seems like I read...
  4. Replies
    10
    Views
    376

    The good thing is when I get home tomorrow it...

    The good thing is when I get home tomorrow it should be sold. If the first person gets it I will be down 100 bucks. If the second or 3rd person gets it I'll break even.
  5. Replies
    10
    Views
    376

    Please do. I also have a 01 Polaris Virage that's...

    Please do. I also have a 01 Polaris Virage that's been a great ski. It had a bog issue that the shop could fix so my friend sold it to me for 2000. Super clean and 145psi on both cylinders, it was...
  6. Replies
    10
    Views
    376

    I took her out yesterday. At first the same damn...

    I took her out yesterday. At first the same damn thing. adjusting the lows did nothing. Took it out and bog till 2500, then ran great. Ran full speed for about 5 minutes then slowed back down to an...
  7. Replies
    10
    Views
    376

    I have been using a small drill bit. This must be...

    I have been using a small drill bit. This must be the 4 or 5th time but I screwed up this time. However I had some small stiff wire that I used the same way with the carbs on the ski. The wire was...
  8. Replies
    10
    Views
    376

    I took another look and I guess I didn't do a...

    I took another look and I guess I didn't do a very good job of adjusting the carbs. with the front carb completely closed I could see a slight gap on the back carb. I backed off the screw just a bit...
  9. Replies
    10
    Views
    376

    New Issue with the SL750

    I have been working on this 95 SL750 for a while now. The last time out I had just replaced one of the coils and it ran the best so far. But it wanted to bog between idle and 2400 rpm if you gave it...
  10. Replies
    21
    Views
    639

    No luck, now to find a 4010558 CDI

    No luck, now to find a 4010558 CDI
  11. Replies
    0
    Views
    128

    looking for a 4010558 CDI

    After as much testing I can do I believe its my CDI that is bad. I replaced the coil and one of the wires but no help. If I go from the blk/wht wire to ground I'll see 90 to 100 volts, but between...
  12. Replies
    21
    Views
    639

    So I pulled the trigger and went for a coil and...

    So I pulled the trigger and went for a coil and plug wire. It's cheaper than the CDI. We will find out when it comes in.
  13. Replies
    21
    Views
    639

    No luck, It looks like the end got pulled hard...

    No luck, It looks like the end got pulled hard and loosened up. I cleaned it up no help. I made a new wire, it's different type but not a damn thing. Maybe order a coil and new wires and see.
  14. Replies
    21
    Views
    639

    Well I be damned unless I damaged the long plug...

    Well I be damned unless I damaged the long plug wire when pulling it off ( it wasn't easy) it's the problem. It reads open, not sure how i got a reading between them
  15. Replies
    21
    Views
    639

    3.5 ohms across the primary, I did not check end...

    3.5 ohms across the primary, I did not check end to end but across the secondary's 8.64K
  16. Replies
    21
    Views
    639

    I haven't seen the 200 but that one time and that...

    I haven't seen the 200 but that one time and that was with the wire pulled off the coil. With the wire hooked up ill get around low 90's. All I can say is there is no voltage at all out of the plug...
  17. Replies
    21
    Views
    639

    i have read that if you change the CDI that you...

    i have read that if you change the CDI that you have to check your timing. Is this the case when ordering a new one with the same part number?
  18. Replies
    21
    Views
    639

    I guess I will order a CDI 4010558, My theory is...

    I guess I will order a CDI 4010558, My theory is 1. the voltage is too low and this would be the CDI, 2. I have voltage but no current, this would explain why there is no secondary voltage at all....
  19. Replies
    21
    Views
    639

    I just double checked with one plug screwed into...

    I just double checked with one plug screwed into the head and the pug wire on, the other plug out but well grounded to the head, no spark.

    So I'm not too sure on a dc coil configuration. but it...
  20. Replies
    21
    Views
    639

    I checked voltage at the primary of the coil....

    I checked voltage at the primary of the coil. With both wires hooked up to the coil I get about 78 volts DC, With one wire hooked up and reading the other side of the coil I get about 100.

    i also...
  21. Replies
    21
    Views
    639

    I put the plugs back in, hooked the charger up to...

    I put the plugs back in, hooked the charger up to maker sure of voltage and tried each plug wire one at a time, no luck.
  22. Replies
    21
    Views
    639

    The voltage when cranking is 11.2, but I have...

    The voltage when cranking is 11.2, but I have both plug wires off.
  23. Replies
    21
    Views
    639

    So I went though the thread that tells you how to...

    So I went though the thread that tells you how to check everything. The only thing that doesn't check out is the hall effect sensor. It's more like 100 ohms.

    Now with that said one of the blk/wht...
  24. Replies
    21
    Views
    639

    I don't see a print that matches my coil. I have...

    I don't see a print that matches my coil. I have a two blk/wh wires going to it and the two plug wires coming out. When I try to start i have about 48 volts AC on the two blk/wht wires. When I ohm...
  25. Replies
    21
    Views
    639

    Need help with my 2000 Virage no spark

    I took my Virage out today and ran around for about 30 miles. No issues at all until I stopped to cool off. Then when I went to leave it started rough, I thought that maybe it was loaded up a bit. I...
Results 1 to 25 of 76
Page 1 of 4 1 2 3 4