Search

Search: Search took 1.00 seconds.

  1. Replies
    3
    Views
    179

    167.5 high speed jets 87.5 low speed jets 2.3...

    167.5 high speed jets 87.5 low speed jets 2.3 needle and seat with stock springs with aftermarket flame arrestors and the accelerator pump still installed. Or a 90 or 95 low with the accelerator...
  2. What I learned last night is that the flywheel...

    What I learned last night is that the flywheel from a 1999 and newer 951 has 4 magnets on it. The 1998 and older have 2 magnets on them. My 1998 Seadoo Ski is getting twice as many pulses from a...
  3. Replies
    0
    Views
    557

    Turbo Lag issue Solved

    All, after years of hair pulling troubleshooting and countless $$ of parts swapping and personal labor my turbo lag is gone. Brian told me over a year ago what the problem was and I didnít listen. ...
  4. Replies
    3
    Views
    265

    Yep, I use a fine wire wheel. NOT the coarse one.

    Yep, I use a fine wire wheel. NOT the coarse one.
  5. Replies
    3
    Views
    265

    A wire wheel on a drill may work.

    A wire wheel on a drill may work.
  6. Replies
    0
    Views
    419

    Installed new grips on 2017 310X

    Kawasaki has been using the same grips for years and I have never liked them. When I had a 2004 15-F, I replaced the grips with a locking ATV grip and liked them. Don't remember the the brand. So,...
  7. Replies
    2
    Views
    588

    Use stainless steel hardware. Put a dab of...

    Use stainless steel hardware. Put a dab of grease on the threads to prevent galling. The angle piece is 3" x 3" x 3/16" stainless angle.
    ...
  8. Replies
    19
    Views
    2,051

    So after a tank of pre-mix I am adjusting the low...

    So after a tank of pre-mix I am adjusting the low speed screws because of a bog on the low end.
    I can start it cold with no choke.

    This setup has F/A's. Regular 87 fuel and stock compression....
  9. Replies
    3
    Views
    1,030

    A group of us will be riding the north end of...

    A group of us will be riding the north end of Lake Saint Clair around the end of July.

    http://greenhulk.net/forums/showthread.php?t=256146&p=2804216&viewfull=1#post2804216

    ...
  10. Replies
    19
    Views
    2,051

    Completed. Got 3 hours on it so far. Running...

    Completed. Got 3 hours on it so far. Running very good. Pretty happy with the way it turned out. I have seen them up for sale for $3500 and $1200. Obviously it is dependant on condition. ...
  11. Replies
    19
    Views
    3,048

    Put flat brackets on the ends of the angled 4x6,...

    Put flat brackets on the ends of the angled 4x6, down to the 2x8.

    Bracket can be wider than 4 inches as long as it doesnít reach too close to the top of the angled bunk.

    You could also run lag...
  12. OTA !! (Oil Thread Alert) Generally agree...

    OTA !! (Oil Thread Alert)



    Generally agree -- “it doesn’t matter as long as you change it regularly”

    Synthetic’s (pao4 oil) only true benefit (and it is a pretty good benefit) is not having...
  13. Well, it IS a cheap price. They don't say how...

    Well, it IS a cheap price. They don't say how thick the metal is on the 2-place. They are made of steel TUBING, which generally sucks. It appears that the bars that the winches are mounted on...
  14. Replies
    7
    Views
    1,510

    The Trailer--Revisited

    I bought a couple of Kawasaki Ultra LXs last fall. There was no way that they would fit on any double trailer I had, but I had a rotted out trailer that I planned to use for parts. I got the...
  15. Replies
    4
    Views
    5,237

    Here

    Here
  16. Blue, I'm in Houston, and there were a few still...

    Blue, I'm in Houston, and there were a few still about here in late 2012, but I didnt see any real deep discounts. Discounts, sure, but nothing to get excited about or want to trade in my sportster....
  17. Here's the other half of what I did. But I really...

    Here's the other half of what I did. But I really like your suggestion. I think I will bring my red cap up a little higher to get as close to flush as I can...I would rather have a little extra...
  18. Here's what I went by from the book when...

    Here's what I went by from the book when rebuilding it. It doesn't make any mention of the tapered needle inside so I think it just gets screwed in tight. Another reason why I think this is because...
  19. Replies
    10
    Views
    1,662

    Here are the pics. The scratched up around the...

    Here are the pics. The scratched up around the switch when I mounted it in the glove box. But I'm trying not to let my OCD make me want to order a new glove box :p
Results 1 to 19 of 22