Search

Type: Posts; User: smokeysevin

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    13
    Views
    307

    In the first post you mentioned you tried the...

    In the first post you mentioned you tried the ecu, what specifically did you do? What is the battery voltage while cranking?

    Sean
  2. Replies
    13
    Views
    307

    Odds are it's not the stator then. The ecu...

    Odds are it's not the stator then.

    The ecu only wants 2 inputs to set the timing, crank position and cam position. Since you have spark on one pair of coils, we know that is working to some...
  3. Replies
    0
    Views
    49

    FS - Parts 215 injectors (6 total)

    Pulled when I swapped from 215 chargers to x chargers on challenger boat a few years back.

    Kept clean and sealed. Worked when removed.

    Make an offer

    Sean

    468319
    468320
  4. Replies
    13
    Views
    307

    Unlikely, what is the battery voltage? Just...

    Unlikely, what is the battery voltage?

    Just as a sanity check here,

    Pull the spark plugs out of the head and connect the plug wires to them, then set them on the valve cover so that the...
  5. Replies
    92
    Views
    2,925

    For whatever reason both replacement sets are...

    For whatever reason both replacement sets are marked that way. They are proper for 83mm bore. They are drop in when used with the correct pins and weigh the same as stock. These were used in a 430hp...
  6. Replies
    92
    Views
    2,925

    Mtcs Sean ...

    Mtcs

    Sean
    ...
  7. Replies
    92
    Views
    2,925

    I would make damn sure whatever you get is...

    I would make damn sure whatever you get is waterproof, or can be made waterproof. The newer holly dashes don't look sealed from what I have seen and also don't look sunlight readable since they all...
  8. Replies
    92
    Views
    2,925

    I know a few people running halltechs on ultras...

    I know a few people running halltechs on ultras with good luck. I ran a megasquirt 3 with ms3x specifically for the customization options and the onboard logging. I am also planning on testing a...
  9. Replies
    92
    Views
    2,925

    I have a set of stock 15f compression forged mtcs...

    I have a set of stock 15f compression forged mtcs waiting on you if you want them.

    Sean
  10. Replies
    12
    Views
    634

    What does the piston look like? Sean

    What does the piston look like?

    Sean
  11. Replies
    3
    Views
    134

    FS - Parts No but I am using it for another project. Sean

    No but I am using it for another project.

    Sean
  12. Replies
    12
    Views
    634

    Can you pull the plug and post a picture of the...

    Can you pull the plug and post a picture of the hole from both sides and a picture of the plug?

    Sean
  13. Replies
    3
    Views
    134

    FS - Parts Parts. Ill snap some more later. Sean ...

    Parts. Ill snap some more later.

    Sean

    http://greenhulk.net/forums/attachment.php?attachmentid=468146&stc=1
    http://greenhulk.net/forums/attachment.php?attachmentid=468147&stc=1...
  14. Replies
    1
    Views
    51

    FS - Parts 2004 STX-12f Engine

    I am running out of time/space to finish this before my first kiddo is born so I am going to pass of my garbage you lucky members!

    All prices are part only, shipping will vary and be extra. PP...
  15. Replies
    3
    Views
    134

    FS - Parts STXR Partout

    I am running out of time/space to finish this before my first kiddo is born so I am going to pass of my garbage you lucky members!

    All prices are part only, shipping will vary and be extra. PP...
  16. Replies
    4
    Views
    123

    I had a 12f motor do the same thing. Make sure...

    I had a 12f motor do the same thing. Make sure you change the oil if it smells like fuel. Mine was really bad.

    Sean
  17. Replies
    92
    Views
    2,925

    Huh, hadn't seen that. Interesting. Sean

    Huh, hadn't seen that. Interesting.

    Sean
  18. Replies
    107
    Views
    9,167

    I may try playing with that, if I move it towards...

    I may try playing with that, if I move it towards the tunnel it starts getting really close to the supercharger inlet.

    Sean
  19. Replies
    92
    Views
    2,925

    The taper on these is intentional, once you get...

    The taper on these is intentional, once you get them off you can see it.

    The rods on the 12f are a proprietary rod, I looked into swapping them but they are not the same dims as the bike. I also...
  20. Replies
    104
    Views
    5,251

    Interesting, I have not used that type before. I...

    Interesting, I have not used that type before. I have odi rogues on my bars right now. What did it cost for the doo grips?

    Sean
  21. Replies
    92
    Views
    2,925

    The first 2 are reasonably easy since you can...

    The first 2 are reasonably easy since you can have 2 up and 2 down. The other 2 are more difficult since you have to have all 4 in line. It is really easy to get frustrated and accidentally pop the 2...
  22. Replies
    92
    Views
    2,925

    Doing the top in method on a kawi 4 stroke...

    Doing the top in method on a kawi 4 stroke requires splitting the crankcase though since the lower section has a cast in windage tray. Im going to go that route when my rings show up but thats only...
  23. You should have a little exclamation mark on the...

    You should have a little exclamation mark on the pm that you were sent, click that and it will report the pm. Im on mobile right now so the process may be different.

    Sean
  24. If you have not done so already, please report...

    If you have not done so already, please report the pms so we can ban them. These bots/scammers are a painin the ass and we are trying to get some system in place to stop it.

    Sean
  25. Replies
    92
    Views
    2,925

    I think its a lead in to make installing the...

    I think its a lead in to make installing the rings easier but I could be wrong, its larger than the bore on the bottom.

    If you stick with 12f rods and crank with zx/12f/15f pistons it will be a...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4