Search

Type: Posts; User: turboman412

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. My bro has that impeller in his stxr, performs...

    My bro has that impeller in his stxr, performs well you will be pleased
  2. Wouldnt worry about it, pumps make noise when not...

    Wouldnt worry about it, pumps make noise when not being submerged in water.
  3. A damaged impeller would hit rev limiter quicker...

    A damaged impeller would hit rev limiter quicker so hitting 7k means nothing. You will be very happy with the solas very good impeller aslong pitched right. My stxr a rocket with the skat it has in it
  4. Replies
    6
    Views
    133

    Br9es are copper plugs

    Br9es are copper plugs
  5. I use the hole for stock discharge for the...

    I use the hole for stock discharge for the tripple pisser, just have to put a peice of hose around pisser fitting to fit bigger hole.

    Can use stock spot for bilge pump but a rule 350 uses a 3/4...
  6. Replies
    6
    Views
    133

    I would try copper plugs and see if it helps

    I would try copper plugs and see if it helps
  7. Replies
    9
    Views
    175

    Agreed, everyone i have had or worked on had hard...

    Agreed, everyone i have had or worked on had hard start issue.
  8. Replies
    2
    Views
    70

    I have one! Pm me

    I have one! Pm me
  9. Replies
    6
    Views
    133

    Hard start is common on these, we normally...

    Hard start is common on these, we normally install primers which cure the starting issue
  10. I never mess with any settings on these carbs...

    I never mess with any settings on these carbs just make sure they are clean.
  11. No concern on plugs, ok to open up just not got...

    No concern on plugs, ok to open up just not got extended periods of time. Keeps rpms fluctuating to seat rings while running
  12. Proper break in is varying rpms short bursts is...

    Proper break in is varying rpms short bursts is fine dont keep rpm the same for long periods of time..

    It is 2019 now so two strokes suck [emoji3526]ill send you a pm later with my opinion...
  13. It happens

    It happens
  14. Not your issue

    Not your issue
  15. Yeah that makes sense your right!

    Yeah that makes sense your right!
  16. I wouldn't run it this way, she will blow or hurt...

    I wouldn't run it this way, she will blow or hurt someone. Theres a massive airleak for it to run away like your decribing
  17. I live in ct, if your not to far i am happy to...

    I live in ct, if your not to far i am happy to help get it going.
  18. An air leak will cause what you described. Oil...

    An air leak will cause what you described.

    Oil cable looks good.

    Over filled balancer will not cause an air leak
  19. They are only 30 inch pounds if i remember right....

    They are only 30 inch pounds if i remember right. I would run and spray brake cleaner around gaskets and see if idle changes unless when you start she runs right away.

    My stxr and ultra have been...
  20. Why does owning a 2 stroke ski suck?

    Why does owning a 2 stroke ski suck?
  21. If its revving to 5k by itself you have an air...

    If its revving to 5k by itself you have an air leak. You can try and spray carb cleaner around gaskets to see if theres a change. But from what your explaining its an air leak and its running away..
  22. Cylinder 3 is last in line for cooling, alot...

    Cylinder 3 is last in line for cooling, alot depends on your water pressure. Its pointless to see how a watercraft engine runs from judging on a hose needs to be i the water with load and proper...
  23. It has an air leak which is why its running away....

    It has an air leak which is why its running away.

    Replace the gasket on exhaust manifold

    Are you testing temps in water or on hose? Running on hose means nothing, you water pressure is lower...
  24. Theres adjustment on the engine side, you have to...

    Theres adjustment on the engine side, you have to make sure that holder is lined up or it will get damaged.
  25. I normally take those seals off and put a rubber...

    I normally take those seals off and put a rubber o-ring. Pretty sure driveshaft from 900,1100 and 1200 are the same.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4