Search

Page 1 of 8 1 2 3 4

Search: Search took 1.00 seconds.

  1. Interior. https://youtu.be/TqxHXvg1Uzo

    Interior.

    https://youtu.be/TqxHXvg1Uzo
  2. The exterior. https://youtu.be/PbdAicGMSkI

    The exterior.

    https://youtu.be/PbdAicGMSkI
  3. Haha still going. She is still afloat but waiting...

    Haha still going. She is still afloat but waiting on me to save the last $30k to finish her up.
  4. Gas engines in marine applications RPMs max out...

    Gas engines in marine applications RPMs max out far under the auto redline. I wish I could make that trip. At best I would take it to Mexico.
  5. Depending greatly on weight and balance between...

    Depending greatly on weight and balance between 2800-3000rpm is where she gets fully on step. At 16-17 knots.
    The original top speed was 22-24 knots at 4200rpm. The new engines top out at 4700 rpm...
  6. Started the new kitchen remodel and and slowly...

    Started the new kitchen remodel and and slowly redoing the decks. By spring the decks should be done as will the new kitchen and main cabin remodel.

    You ou never know it may be ready for some fun...
  7. I am afraid it's party cruise will wait until the...

    I am afraid it's party cruise will wait until the exterior work is finished. She took a beating this last winter out of the water and uncovered and she needs work. But it's just paint and varnish so...
  8. Thanks. Now to recover financially a bit then...

    Thanks. Now to recover financially a bit then move back on to the exterior and interior.
  9. It's first outing went well but was cut short by...

    It's first outing went well but was cut short by the fact it has not been out in over a year. So the front needs to swell back up before I can sustain more than 4 mph. Otherwise it takes on water...
  10. Now to clean it up and take it out for a shake...

    Now to clean it up and take it out for a shake down cruise.

    https://youtu.be/7tEz0B4b57Y


    I also got some time to remove the wet bar up top as well as the refrigerator and ice maker. No need...
  11. This happened today! ...

    This happened today!

    https://youtu.be/PwRnJ2Yz3MM

    Time to connect the cables, cut the shaft lines and pull her out for a shake down.
  12. The starboard engine hanging from the frame and I...

    The starboard engine hanging from the frame and I beam during the final install process.
    https://youtu.be/GDhtY_lrpSU

    The engine is in and ready for plumbing. It should be ready to start...
  13. The new shit tank! It's an old30 gallon steel...

    The new shit tank! It's an old30 gallon steel tank I took from the front head. I don't need two bathrooms in this boat so I took the biggest tank and recycled it.

    After a fresh coat of paint. ...
  14. This last week I installed the port house battery...

    This last week I installed the port house battery bank. Four 370 amp hour 6 volts. I also made a new box for them.
    ...
  15. This happened today ...

    This happened today

    https://youtu.be/QqdkEFoi0I0
  16. A quick video of the finished install on the port...

    A quick video of the finished install on the port engine. There were lots of bolts and little items to deal with. I could have just bolted itnto the wood stringers but I felt that was nuts :smt119
    ...
  17. My brother is a drone photographer so yes.

    My brother is a drone photographer so yes.
  18. Waiting on the shift throttle controls to arrive...

    Waiting on the shift throttle controls to arrive otherwise ready to hit the water. ...
  19. The new Mercury 20 hp for the little dingy. Just...

    The new Mercury 20 hp for the little dingy. Just waiting on cables and the start/shift/throttle controller to arrive. ...
  20. I do have several pwc but you have to tow them...

    I do have several pwc but you have to tow them and they are heavy and I know from experience they are not to fun to fish from. To that end I have been looking for a small center console runabout.
    ...
  21. Ok a much awaited week. I designed made the...

    Ok a much awaited week.

    I designed made the new engine mounts. I tried to keep it as simple as possible. The flat pieces will gain into the inside of the stringer where the transmission mounts...
  22. When I say build the plug I mean build it pin by...

    When I say build the plug I mean build it pin by pin. The sea gauge system is diy. No plug and play.

    ...
  23. Got the basic wiring of the seagauge interface...

    Got the basic wiring of the seagauge interface module done. Only temp,oil pressure, volts, and rpm, for now. I need a temp sensor for the engine oil, another tempnsensor for the transmission fluid,...
  24. Working and setting up for the final on the...

    Working and setting up for the final on the mechanical install. Getting the timing correct to get me and my friend on the boat together to get it done is the hardest part atm. He has lots of kids and...
  25. No update this week. I needed to get a money...

    No update this week. I needed to get a money maker of mine ready for the season. I own a 34' boat 15ton trailer that I can use to haul almost any boat up to 34'. It's easy
    money especialy if they...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4