Search

Type: Posts; User: Cosmicbrut

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    221

    https://rivaracing.com/file/7288-RS15050-SK-O2+-+S...

    https://rivaracing.com/file/7288-RS15050-SK-O2+-+Sea-Doo+O2+Sensor+Installation+Kit.pdf

    This should give you the answers you need.
  2. Replies
    174
    Views
    14,036

    Im running a dashpac on my 2019 with the digital...

    Im running a dashpac on my 2019 with the digital cluster. Its comes up under the depth function and you can toggle between afr/boost/engine temp. Maptuner works fine but i dont flash through the...
  3. Replies
    0
    Views
    133

    SOLD 2014 and Later Jet Pump

    Looking to buy a 2014 or later 159/161 jet pump. PM me with what you have.
  4. Replies
    122
    Views
    8,757

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=461946&stc=1
    Dash is off quite a bit
  5. Replies
    6
    Views
    1,401

    On both my 300s 145-155 is the range they were new

    On both my 300s 145-155 is the range they were new
  6. Replies
    60
    Views
    8,129

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=457788&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=457789&stc=1
  7. Replies
    8
    Views
    827

    The reason you want a check valve is because the...

    The reason you want a check valve is because the pump tunnel is under vacuum until roughly 25-30 mph. Having the check valve keeps air from going into the tunnel which creates terrible cavitation. So...
  8. Replies
    4
    Views
    688

    I have it written down somewhere but it was...

    I have it written down somewhere but it was between .210 and .215 inches
  9. Replies
    4
    Views
    710

    The 300 gasket is compatible with a 4tec it will...

    The 300 gasket is compatible with a 4tec it will lower your compression about a tenth of a point because its thicker. The valves are the same as well.
  10. Replies
    4
    Views
    688

    About .248 lift on both intake and exhaust lobes

    About .248 lift on both intake and exhaust lobes
  11. Replies
    3
    Views
    663

    If its only when running then most likely one of...

    If its only when running then most likely one of the hoses coming from the pump to to cool the intercooler or exhaust came off or has a hole in it.
  12. http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=455381&stc=1
    I’m starting to think this crack isn't an isolated incident. This is the 4th ski Ive heard of the pump tunnel cracking. The...
  13. Replies
    2
    Views
    427

    SOLD Nope 1500 grit on a block with wd 40

    Nope 1500 grit on a block with wd 40
  14. i had a similar issue earlier this year when the...

    i had a similar issue earlier this year when the water was cooler. I went through an o2 sensor really fast and noticed water droplets on the sensor.Pressure tested the water jacket on the manifold to...
  15. Replies
    8
    Views
    631

    The 2018 and newer cooling systems are quite...

    The 2018 and newer cooling systems are quite efficient compared to older closed loop setups. Ive got over 60 hours spinning 8800+ on my 2018 px and the hottest Ive seen it get was 181 and no coolant...
  16. Replies
    2
    Views
    427

    SOLD Eastside built 4tec Head

    Head out of a 2014 rxt x 260. Bronze valve guides, Supertech stainless valves with springs and retainers. Fully built and ported by Eastside.Asking $1500 but open to offers.
  17. Replies
    6
    Views
    950

    SOLD The cam will work on a 260 or 300. Waterbox is...

    The cam will work on a 260 or 300. Waterbox is still available
  18. Replies
    22
    Views
    1,850

    Pm slow91 on here thats chris from eastside

    Pm slow91 on here thats chris from eastside
  19. Replies
    22
    Views
    1,850

    Eastside for sure. You can just upgrade the...

    Eastside for sure. You can just upgrade the guides and valves or port too. The porting makes it hit a lot harder.
  20. Replies
    9
    Views
    687

    Ive had a 19 tx in rough water and it’s one of if...

    Ive had a 19 tx in rough water and it’s one of if not the best hull for rough water that ive rode. The handlebars are adjustable so you can ride standing up comfortably.
  21. Replies
    125
    Views
    24,109

    According to their website the tx is coming with...

    According to their website the tx is coming with a 18.5 gallon gas tank (edit) All ST3 hulls
    http://greenhulk.net/forums/attachment.php?attachmentid=453655&stc=1
  22. Replies
    6
    Views
    950

    SOLD Bump

    Bump
  23. Thread: Dashpac

    by Cosmicbrut
    Replies
    0
    Views
    244

    SOLD Dashpac

    http://greenhulk.net/forums/attachment.php?attachmentid=453300&stc=1

    Dashpac for sale, will work on skis up to 2018. $225 shipped
  24. Replies
    19
    Views
    884

    The tuning license is locked to the vin number of...

    The tuning license is locked to the vin number of the original ski. If you changed it to what your vin is thats why it isnt working. Buds 2 can change the vin number i do believe.
  25. Replies
    6
    Views
    950

    SOLD http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=453029&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=453030&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=453031&s...
Results 1 to 25 of 104
Page 1 of 5 1 2 3 4