Search

Type: Posts; User: Spades

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    84

    Failing ignition pickup coil?

    What are the symptoms of a failing ignition pickup coil? The ski runs good for about 30 seconds, then starts to chug down progressively until it cant throttle up anymore, but it will always idle. If...
  2. Replies
    12
    Views
    435

    Verify that the plugs themselves are sparking

    Verify that the plugs themselves are sparking
  3. WTB - Parts R&D intake scoop grate?

    R&D intake scoop grate?
  4. Replies
    5
    Views
    234

    im getting a used OEM, this will be for an 01 RX...

    im getting a used OEM, this will be for an 01 RX carb. I read that the 4-Tec rectifiers are good heavy duty upgrades, are the GTX-DI or RX-DI rectifiers just as good?

    ***Also found another from an...
  5. Replies
    5
    Views
    234

    Im more worried about damaging the MPEM. Im...

    Im more worried about damaging the MPEM. Im hoping it has an over-voltage protection.. But either way im now in contact with the supplier
  6. Replies
    5
    Views
    234

    New rectifier - charging voltage too high?

    Just installed a Caltric rectifier from ebay. Charging voltage at startup (on the trailer) is at 13.2V, then after a quick snap of throttle and letting it settle back down to idle its at 14.1V, but...
  7. a 90 LS jet should do it

    a 90 LS jet should do it
  8. Replies
    3
    Views
    247

    Did you use the 40mm or 38mm Polaris carbs? And...

    Did you use the 40mm or 38mm Polaris carbs? And would you mind sharing your jetting specs?
  9. Replies
    6
    Views
    478

    Yes single Triton, torsion axle. Never backed...

    Yes single Triton, torsion axle. Never backed into anything or any damage, I will take pics later this evening. I didnt see any cracks but i am worried to create one when bending back upwards
  10. Replies
    6
    Views
    478

    yes the frame has bent downward, starting from...

    yes the frame has bent downward, starting from immediately after the axle. Im trying to think of a way to hold down the frame just above the axle area while i use a floor jack to lift the tail end....
  11. Replies
    6
    Views
    478

    Triton Elite wc1 sagging at the rear end

    My Triton Elite trailer has sagged about 2" at the rear, both sides look equally sagged making me question if It had always been that way but I doubt it. The gvwr is 1150 and my ski is only 740 lbs....
  12. Replies
    11
    Views
    888

    Oh wow i havent been on here in a very long time...

    Oh wow i havent been on here in a very long time :)

    Here is a thread i created when i had the Polaris CDK-40 carbs all mounted up on Kawi 1200 manifold. The difference in spacing was minimal...
  13. Replies
    2
    Views
    436

    inspect the water log manifold that feeds the 3...

    inspect the water log manifold that feeds the 3 cylinders, a common leak point that isnt visible, youd have to feel for the leak
  14. Replies
    10
    Views
    1,039

    FS ttt

    ttt
  15. Replies
    8
    Views
    934

    FS ttt

    ttt
  16. Replies
    10
    Views
    1,039

    FS ttt

    ttt
  17. Replies
    8
    Views
    934

    FS 671baja - Yes, i still have the exhaust system ...

    671baja - Yes, i still have the exhaust system

    erock, paypal works
  18. Replies
    24
    Views
    2,779

    I would check for over-voltage on that lead (with...

    I would check for over-voltage on that lead (with engine running). If its over then the new LED lights could burn up also, although the LEDs will have a wider acceptable range
  19. Replies
    8
    Views
    934

    FS Didnt know i got a reply on this, i never got a...

    Didnt know i got a reply on this, i never got a notification
  20. Replies
    10
    Views
    1,039

    FS ttt

    ttt
  21. If it has the anti-rattle cone, make sure it isnt...

    If it has the anti-rattle cone, make sure it isnt the anti-rattle assembly that is contributing to the tightness



    I dont recall a washer in between the hull and pump, only on the outside of the...
  22. Replies
    16
    Views
    2,383

    The double hitch receiver is the simplest...

    The double hitch receiver is the simplest solution, however you can no longer open the tailgate when mounted, which is why i opted to mount it behind the trailer.
  23. Replies
    16
    Views
    2,383

    Here is my solution. I custom mounted a hitch...

    Here is my solution. I custom mounted a hitch receiver on the rear beam of the trailer

    http://greenhulk.net/forums/attachment.php?attachmentid=439872&stc=1
  24. Replies
    10
    Views
    1,039

    FS still for sale

    still for sale
  25. Replies
    8
    Views
    934

    FS ttt

    ttt
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4