Search

Type: Posts; User: Jonesyfxr

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Island Racing can rebuild them, I think Group K...

    Island Racing can rebuild them, I think Group K can as well.

    Best of luck!!

    I'd recommend waveater clips, D plate install along with PV couplers while you're in there.
  2. Don’t forget to clunk the fuel pickups in the...

    Don’t forget to clunk the fuel pickups in the tank.
  3. Replies
    17
    Views
    14,944

    The cylinders usually have a letter cast into it....

    The cylinders usually have a letter cast into it. The letter corresponds to the correct piston size. The piston size would dictate the cylinder wall clearance.
  4. Replies
    24
    Views
    2,968

    View Post

    Ok.... the temp sensor isn’t plugged in, hence the alarm. The ski won’t start without it plugged in.
  5. Replies
    24
    Views
    2,968

    Make sure your pulse lines are tight.

    Make sure your pulse lines are tight.
  6. Replies
    24
    Views
    2,968

    You might have an air leak somewhere. We rebuilt...

    You might have an air leak somewhere. We rebuilt our carbs and used clear tygon fuel lines. As soon as we turned the engine over the fuel pumps drew the fuel into the carbs within seconds.

    Did...
  7. Replies
    102
    Views
    7,219

    Congratulations!!!

    Congratulations!!!
  8. Replies
    24
    Views
    2,968

    Is your fuel selector working properly?

    Is your fuel selector working properly?
  9. Replies
    24
    Views
    2,968

    Did you reconnect the pulse lines from each...

    Did you reconnect the pulse lines from each cylinder to the carbs?
  10. Replies
    24
    Views
    2,968

    No problem dude!!! Best of luck!

    No problem dude!!!

    Best of luck!
  11. Replies
    24
    Views
    2,968

    Yes... that drawing is wrong. Original routing is...

    Yes... that drawing is wrong. Original routing is from selector to filter to inlet on PTO carb. Return is out the front carb.
  12. Replies
    18
    Views
    1,848

    Mike, Not so well. She wants to run, but the...

    Mike,

    Not so well. She wants to run, but the idle is low. Then we had a little too much fuel load up in the pipe, causing a backfire that pushed the straight pipe sleeve off. We have to check the...
  13. Replies
    3
    Views
    249

    It’s called Graphene nano coating

    It’s called Graphene nano coating
  14. Replies
    102
    Views
    7,219

    Thanks dude!!! She fired up, but we’ve gotta dial...

    Thanks dude!!! She fired up, but we’ve gotta dial in the idle.
    Now that we know it’ll run, the Advent is going in!!
  15. Replies
    102
    Views
    7,219

    We finally installed our carbs the other day. We...

    We finally installed our carbs the other day. We went with 1.5 N&S, 80 gram spring, all stock jets, 1 out on lows with 1 3/8, 1 3/8, 1 1/2 on the highs
  16. Replies
    3
    Views
    249

    303 just came out with a protectant that is...

    303 just came out with a protectant that is supposedly better than ceramic.
  17. Replies
    1
    Views
    124

    Welcome to the site!!! Tons of information on...

    Welcome to the site!!! Tons of information on here.

    http://greenhulk.net/forums/showthread.php?t=286812&highlight=Pump+seal

    There is a search function on the upper right of the page... it...
  18. Replies
    4
    Views
    186

    We are running pre mix, if you’re interested in...

    We are running pre mix, if you’re interested in ours send me a PM.
  19. Sounds like you accelerator pump is bad. ...

    Sounds like you accelerator pump is bad.

    Google search for a manual. I found one online for free.
  20. Replies
    18
    Views
    1,848

    Thanks bro!!! We just got that carbs back in...

    Thanks bro!!!
    We just got that carbs back in and yesterday we finished installing the pipe.... and my back is screaming this morning!!
  21. Replies
    312
    Views
    206,457

    Sticky: The D plate was developed to create some back...

    The D plate was developed to create some back pressure.... without it the ski is a dog.
  22. Replies
    18
    Views
    1,848

    Thanks for the tips. Which flange gasket gets...

    Thanks for the tips. Which flange gasket gets modified?? The one at the head pipe or the larger one at the U pipe?
  23. Try here: ...

    Try here:

    https://pro-tec.us/carbon-tech/168-carbon-tech-reed-set-ht-120066v-1300.html
  24. We have a R&D 800R intake grate with the seal kit...

    We have a R&D 800R intake grate with the seal kit installed. We had the carb issue after Memorial Day weekend. The seal kid definitely helped prevent ventilation and the holeshot bite was immensely...
  25. Our pump seal kit included an insert for are #2....

    Our pump seal kit included an insert for are #2. We had to trim ours to fit flush but then had some carb issues, so our season was short last year.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4