Search

Page 1 of 8 1 2 3 4

Search: Search took 1.00 seconds.

  1. I agree, use a decent quality oil - any further...

    I agree, use a decent quality oil - any further optimization is marginal.

    Most of us change the engine oil (in a 4-stroke watercraft) way before it degrades enough to risk the engine.

    Most of...
  2. Replies
    6
    Views
    242

    since you have unhooked the nozzle and it still...

    since you have unhooked the nozzle and it still steers hard next un hook the cable where it connects to the handlebars, if the handlebars turn freely then the cable is the problem and needs...
  3. Replies
    3
    Views
    145

    I would recommend running a thread chaser through...

    I would recommend running a thread chaser through the hole before putting another spark plug in it. Put anti-seize compound on the plug threads (a little goes a long way). Do NOT overtighten the...
  4. Replies
    5
    Views
    227

    I believe comment about keeping the pump wet is...

    I believe comment about keeping the pump wet is meant to say there is water flushing that way too. That line needs flushed as well. Dosen't have anything to do with cooling the pump.
  5. So I had a chance to take the ski out for a...

    So I had a chance to take the ski out for a little test run on Saturday and was mostly happy with it. I say mostly because when I was on flat water I absolutely loved it, but when I was driving...
  6. View Post

    SOLVED! Camshafts were reinstalled 180° off rotation. That's why it would run perfectly without the sensor plugged in but would not run with the sensor obviously. Solved by Bruce McKenzie
  7. The old Kawasaki throttle is thumb throttle. The...

    The old Kawasaki throttle is thumb throttle. The old SD throttle is a "web" throttle and is actually my favorite. My 03 XP uses it. I hate finger throttles for many reasons. As a motorcycle...
  8. It`s not hard to do and the kit will do many....

    It`s not hard to do and the kit will do many. Before you know it, you will be a pro at installing one. Should just take about four minutes to do one. This will be a good thing to know further down...
  9. Replies
    14
    Views
    1,017

    We built two skis one with exhaust and one with...

    We built two skis one with exhaust and one with the Tj mod. Nearly identical speed wise.
  10. The best bet is to repair the threads with a...

    The best bet is to repair the threads with a HeliCoil insert. Fast, easy and stronger. Kit should cost you 30-40 $
  11. Replies
    73
    Views
    6,096

    With regards to heads cracking and people with...

    With regards to heads cracking and people with experiance with them. I Just have a question. Are the Core plugs screwed into the head between the sparkplug holes Steel or Aluminum?
    If the are steel,...
  12. I checked the voltage every time I had the issue...

    I checked the voltage every time I had the issue and it was resting at 12.5 and would not drop below 12 under load using a battery load tester.



    I looked and there are no chews or knicks in the...
  13. Just quoting the beginning and end due to the...

    Just quoting the beginning and end due to the long nature of your post.

    TimeBandit is a stand up guy for sure as proves here. Kudos Sir for taking the time to help like that.
  14. Replies
    35
    Views
    3,064

    Could be a clutch problem Or split manifold...

    Could be a clutch problem
    Or split manifold dampener
  15. Replies
    21
    Views
    1,700

    I have an 08 sho and have had earth block off...

    I have an 08 sho and have had earth block off twice wasn’t planning on doing it again but one thing I have found is these skis seem very sensitive to high impedance faults as well as continuity check...
  16. Replies
    10
    Views
    1,826

    Anything boosted will NOT run right with a non...

    Anything boosted will NOT run right with a non boost ecu. The computer cannot compensate. Maybe he's done spending money cause he bought the wrong ecu.......you'll never get the truth about that lol!
  17. Replies
    28
    Views
    1,975

    You press against the shaft on the other end. Not...

    You press against the shaft on the other end. Not the back of the coupler
  18. Replies
    28
    Views
    1,975

    The coupler is a solid piece, so yours is...

    The coupler is a solid piece, so yours is damaged. It's a direct opening to the outside of the hull and although the pump shaft sits inside of the mid-shaft, I'd have to guess water will enter the...
  19. Looks pretty simple...

    Looks pretty simple http://partsfinder.onlinemicrofiche.com/4tec/showmodel.asp?type=13&make=yamahapwc&a=262

    check valve at tank end, separator in the middle, vent at the top.....

    vent let’s air...
  20. Thread: DIY Stereo rxtx

    by tchies
    Replies
    4
    Views
    403

    DIY Stereo rxtx

    Thought the $1K stereo was a bit high so I installed my own - $100. am/fm,blue tooth, aux, usb, waterproof

    Works great as I usually just want the radio..
  21. Replies
    12
    Views
    792

    FS - Parts Looks like it rotted thru and cracked. If it was...

    Looks like it rotted thru and cracked. If it was just a hole, I'd take a shot at brazing it. But I wouldn't even try to fix the crack.

    I'd guess it was left to freeze with water in the block. ...
  22. Replies
    24
    Views
    2,356

    Steve's cart is way better than anything else...

    Steve's cart is way better than anything else I've seen.

    But I'd add one more upgrade to the design. I'd set something up to be able to mount a tongue and a winch post. It would be great to be...
  23. Replies
    28
    Views
    1,385

    Let me clear up some misconceptions here. The...

    Let me clear up some misconceptions here. The 655 hour limit talked about here has nothing to do with any limitation of diagnostic software, whether old or newer YDS or Candoopro.It has everything...
  24. Replies
    28
    Views
    1,385

    Does the same 655 hour limitation apply to the...

    Does the same 655 hour limitation apply to the most recent Yamaha diagnostics software, or the CanDOOPro diagnostics software?
  25. Hey, TimeBandit! You know what, you’re right and...

    Hey, TimeBandit! You know what, you’re right and I ‘SHOULD’ know that (but, I failed to keep it first and foremost :-/

    Update: I think the charger in question has gone tots up :-/ - - my wife...
Results 1 to 25 of 186
Page 1 of 8 1 2 3 4