Search

Type: Posts; User: Jhubbs255

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    44
    Views
    8,183

    So your saying.. riding a pwc is not essential......

    So your saying.. riding a pwc is not essential... I will test this out come may ish lol
  2. Replies
    27
    Views
    1,818

    Thanks to all I will be posting speeds soon but...

    Thanks to all I will be posting speeds soon but fired up for the first time today after my first engine removal with fly wheel bolts, lapping valves, new 137+4, injectors and flash. Through the...
  3. Replies
    29
    Views
    418

    Not yet to cold out. Install afr guage this week...

    Not yet to cold out. Install afr guage this week won't got out for actual testing until June probably unless may gets real warm real quick
  4. Replies
    29
    Views
    418

    I'm no mechanic but I just did this thanks to...

    I'm no mechanic but I just did this thanks to much help from this forum

    Bag and lable bolts 100% like he said, take good pics, torque wrench, be carful when you take the PTO cover off the starter...
  5. Replies
    5
    Views
    312

    Thanks. not bad for 350 for the entire paint job...

    Thanks. not bad for 350 for the entire paint job snowing again.... I just need some 80 degree days. This site has made it possible. Cannot thank the ppl on here enough. Hopefully I can return the...
  6. Replies
    5
    Views
    312

    Thanks ncdoo The blue is all rattle can with...

    Thanks ncdoo

    The blue is all rattle can with many coats of primer and clear the black is all shot with my buddies portable paint shop it's actually rim paint hopefully holds up

    3 coats black...
  7. Replies
    5
    Views
    312

    Looking good.. afr wire questions

    459030

    So it's looking good, painted, motor back in , going to install an lc1 innovate wideband tomorrow. Where are you guys connecting the power to. Red to pos. on battery but what about power...
  8. Replies
    14
    Views
    615

    I'm currently doing those mods to mine. Don't...

    I'm currently doing those mods to mine. Don't forget fill ride plate Holes and trim reverse bucket there free. As far as not getting into the engine, 4 inch intake r&d intake grate, 15/20 prop,...
  9. Replies
    27
    Views
    1,818

    Well guys I wanted to say thank you for all you...

    Well guys I wanted to say thank you for all you information. Engine installed prepping for paint now. I was wondering if anyone could predict my speeds with my new mods. Total I have.... Rrfpr,...
  10. Replies
    26
    Views
    1,670

    There are a lot of threads and some some very in...

    There are a lot of threads and some some very in depth testing done side by side with the intake setups. As far as least restricted and BEST performance by a good bit the Riva rear won... BUT...
  11. Thread: Tops valve

    by Jhubbs255
    Replies
    8
    Views
    526

    Someone has got to no how this ball is supposed...

    Someone has got to no how this ball is supposed to act?
  12. Replies
    26
    Views
    1,670

    I agree with riverrat.... That holeshot is the...

    I agree with riverrat.... That holeshot is the 255's fun factor and trademark to me. I have NOT tried a reduction nozzle but spent hours researching it and what I came up with is no matter what even...
  13. Replies
    3
    Views
    237

    WTB - Parts Talking to me I think

    Talking to me I think
  14. Replies
    4
    Views
    304

    After reading what happens to you I'll be...

    After reading what happens to you I'll be checking for sure.
  15. Replies
    4
    Views
    304

    Thanks guys. I do have a manual but didn't see...

    Thanks guys. I do have a manual but didn't see anything on front to back alignment. From what you guys are saying it sounds like it's fine but I'll measure the shaft. With the alignment tool connect...
  16. Replies
    4
    Views
    304

    Engine alignment question

    I installed my engine today and I get how to do the side to side and up and down alignment. My engine shift slightly front to back does this matter? I push it as far as I can up to the front and...
  17. Replies
    6
    Views
    346

    FS - Parts What size are these

    What size are these
  18. Thread: Tops valve

    by Jhubbs255
    Replies
    8
    Views
    526

    Please anyone know the real operation of this. I...

    Please anyone know the real operation of this. I know what's its suppose to prevent but what's this bearing for?
  19. Thread: Tops valve

    by Jhubbs255
    Replies
    8
    Views
    526

    I thought that's what the cylinders did inside...

    I thought that's what the cylinders did inside the valve so is the Bering supposed to not be able to fit through
  20. Replies
    3
    Views
    276

    Wouldn't water run into your exhaust manifold and...

    Wouldn't water run into your exhaust manifold and then into your head
  21. Thread: Tops valve

    by Jhubbs255
    Replies
    8
    Views
    526

    Anyone know how this happened? Nothing looks...

    Anyone know how this happened? Nothing looks damaged inside and it passes the blow test. What does this ball even do
  22. Thread: Tops valve

    by Jhubbs255
    Replies
    8
    Views
    526

    458056 ]this is...

    458056
    ]this is what I'm talking about I can tip the valve upside down and to the side and the ball rolls out. Nothing looks damaged and IV not had any issues with it...
  23. Thread: Tops valve

    by Jhubbs255
    Replies
    8
    Views
    526

    Tops valve

    When I removed the valve disassembling the motor the metal ball inside just fell out. It passes the mouth blowing test but I can tip it upside down and to the side and the ball rolls out of the hose...
  24. Replies
    3
    Views
    237

    WTB - Parts Rxpx 255 start and vts metal housing

    Took mine off and busted the bolts tried to drill out and made things worse lol that's soooofft metal. So looking for housing. Maybe just back piece
  25. Replies
    2
    Views
    351

    Has anyone heard of a good visor/access assembly...

    Has anyone heard of a good visor/access assembly cover air intake. When I got the ski the visor is different. It's raises, and there's a 4" hole cut inside it like a pipe was ment to run to it. I...
Results 1 to 25 of 198
Page 1 of 8 1 2 3 4