Search

Type: Posts; User: casey67

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    16
    Views
    877

    Chamfering is simply removing any sharp edge at...

    Chamfering is simply removing any sharp edge at openings so that the rings will not get snagged.
    Look at the angles at the openings of the cylinders BEFORE it gets bored.
    Anybody that bores...
  2. Replies
    10
    Views
    230

    It's not that bad. At $700 it's still worth it,...

    It's not that bad. At $700 it's still worth it, not as great as the $600 deal but those don't happen that often.
    During the summer,running Genesis sold for an average $2000.

    Id pull the heads...
  3. Replies
    11
    Views
    278

    We have all been new to Polaris at some point....

    We have all been new to Polaris at some point. Yeah, there have been alot of great people contribute to the forums, everyone has tried hard to keep info as accurate as possible. Sometimes there is a...
  4. Replies
    11
    Views
    278

    The "P" is for projected. It sits further into...

    The "P" is for projected. It sits further into the cylinder then plugs without P.

    Again Polaris strangely listed BPR9ES for only the 2001 1200.I tried both in my 1200 with no difference at all....
  5. For got to mention, the 448 was specific to the...

    For got to mention, the 448 was specific to the update kit. But really any 2 cylinder CDI timing curve will be really close. In like 2003 Polaris used a "high start" CDI that made timing a little...
  6. There does seem to be a supply shortage at this...

    There does seem to be a supply shortage at this time. I would have to guess because to the world wide pandemic.

    When new Genuine PVL CDI were available, they did cost $350-$400. Used were around...
  7. Replies
    11
    Views
    278

    Not sure why the Polaris manual has 8's listed,...

    Not sure why the Polaris manual has 8's listed, all other 1200's even the 99 X45 use 9's.
    As xlint mentioned the 8's are hotter=too hot damages pistons.

    I would use the BR9ES , it is safer and...
  8. The burnt wires appear to be from the handle bar...

    The burnt wires appear to be from the handle bar controls harness.
    Did you say you took the switch apart ?
  9. Timing ? What IS the spec for pop-off ?...

    Timing ?

    What IS the spec for pop-off ?
    Needle arm heaight set ?
    Needle arm diaphragms correctly installed/facing correct direction ?
  10. Replies
    15
    Views
    271

    Correct, SLX has a taller box then your Virage. ...

    Correct, SLX has a taller box then your Virage.

    Not sure why Polaris added the second box for 2 years ? of the SLTX. Only advantage I can think of is a shorter MFD harness ( SLTX has MFD in the...
  11. Replies
    15
    Views
    271

    So you have a S L T X ? Maroon 3 seater ?

    So you have a S L T X ? Maroon 3 seater ?
  12. Replies
    15
    Views
    271

    SLX 1 ebox SLTX 2 eboxes ...

    SLX 1 ebox
    SLTX 2 eboxes

    https://parts.polarisind.com/Browse/Browse.asp
  13. Replies
    15
    Views
    271

    Plastic electrical box for 1999 SLX.

    Plastic electrical box for 1999 SLX.
  14. Replies
    15
    Views
    271

    On top of the battery, battery and box are held...

    On top of the battery, battery and box are held down with 2 rubber straps.
  15. Replies
    15
    Views
    255

    Red/pur is the fused battery power wire. It...

    Red/pur is the fused battery power wire. It distributes power to the entire ski.

    Orange is the switched power wire. The LR gets a signal that the engine is running (yellow wire).An AC volts signal...
  16. Replies
    6
    Views
    206

    WTB Yeah, and give your phone number to ANY company,...

    Yeah, and give your phone number to ANY company, sit back and watch all the spam calls/ scammers/politicians come in !
  17. Replies
    6
    Views
    206

    WTB NON-SCAMMER ,PM sent....lol.. Dear friend please...

    NON-SCAMMER ,PM sent....lol.. Dear friend please consider.
  18. Replies
    16
    Views
    643

    Exactly. You never really know the entire...

    Exactly. You never really know the entire procedure unless you do it yourself or have a really good technician that refuses to do things wrong/halfway.

    I agree, starting with truely clean oil on a...
  19. Replies
    16
    Views
    256

    Yes, If you plan on having a second jetski on...

    Yes, If you plan on having a second jetski on that trailer, those tires will hold the weight.

    If you are only going to have the Genesis alone on that trailer the standard 4.80-12 will be fine.
  20. Replies
    16
    Views
    643

    Turbo's spin at really high rpm's, like double...

    Turbo's spin at really high rpm's, like double triple engine rpm. It's pretty rough on oil.
  21. Good enough. That blue sticker has the part...

    Good enough.
    That blue sticker has the part number. https://parts.polarisind.com/AdvancedSearch/AdvancedSearch.asp

    They are the stock 40mm, no accell pump, 2 jet carbs.
    Looks like the stock...
  22. Replies
    16
    Views
    256

    That trailer should be fine,looks like you have...

    That trailer should be fine,looks like you have alot of adjustment and options.
    the Genesis hull strakes are 29inchs. You could set the bunks with 29" gap at inside edges.

    The Genesis is heavy,...
  23. Replies
    16
    Views
    256

    The boards are like 4 inches wide, every trailer...

    The boards are like 4 inches wide, every trailer I have seen puts the boards on a hull ridge.
    So it becomes a matter of personal choice.

    Place the bunks as far apart as adjustment allows.

    I...
  24. Post a picture of the carbs.

    Post a picture of the carbs.
  25. ? He asked for advice. We told him exactly what...

    ?
    He asked for advice. We told him exactly what IS wrong.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4