Search

Type: Posts; User: jetdawg701

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    649

    I've had real good luck with the RL-HM026A...

    I've had real good luck with the RL-HM026A tachometer. It's very easy to read in bright or cloudy daylight, stays dry, very accurate and the price is less than $20RL-HM026A
  2. Not exactly sure what you're experiencing but it...

    Not exactly sure what you're experiencing but it could be supercharger surge. My Tial BOV had an 8lb spring and shuddered between 10-20ish mph until I replaced it with a lighter 2lb spring. I believe...
  3. My '17 GP1800' with original/OEM clutch lasted 80...

    My '17 GP1800' with original/OEM clutch lasted 80 hours running Riva stage 2+@ 87mph, I then purchased a "CR" clutch from Dean, drilled the holes in the bolt per instructions and it currently has 170...
  4. Replies
    8
    Views
    639

    View Post

    I’ll assume this is a GP1200 that you’re referring to. I don’t believe this is from water ingestion, it looks like oil starvation to me. Did you check the oil injection lines that feed each cylinder?...
  5. Replies
    6
    Views
    510

    With the valve cover off, reach in there with a...

    With the valve cover off, reach in there with a long screwdriver or a stick and just tap or bump the plastic guide which rests against the tensioner, this will release the tensioner and will apply...
  6. Does the engine crank over or is the starter just...

    Does the engine crank over or is the starter just spinning the flywheel? Stock flywheel bolts are known to break on these engines.
  7. Very cool. Any welding, cutting or notching of...

    Very cool. Any welding, cutting or notching of the bar ends involved?
  8. Replies
    13
    Views
    981

    I had the Worx sponsons on my GP1800 for two...

    I had the Worx sponsons on my GP1800 for two rides before removing them. They were very aggressive in low position or tame in upper position. I noticed that the ski was a bit less stable with a...
  9. Replies
    33
    Views
    3,584

    I sealed my Gp1800 transom plate with 4200 and it...

    I sealed my Gp1800 transom plate with 4200 and it started leaking after first or second ride so I did it again with 5200 fast cure and it fixed the issue although future removal of transom will be a...
  10. Replies
    43
    Views
    3,092

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=446355&stc=1
    I’ve had no issues removing several impellers, (knock on wood) including the stock impeller while using this wood block method....
  11. I used a hot glue gun to fill the voids in the...

    I used a hot glue gun to fill the voids in the rubber seal.
  12. Riva does say to run the dedicated intercooler...

    Riva does say to run the dedicated intercooler water exit line from I/C to the oil cooler then exit at left side of boat only, but I ran my straight into the right side pissers just like stock. I...
  13. http://www.greenhulk.net/forums/attachment.php?att...

    http://www.greenhulk.net/forums/attachment.php?attachmentid=425211&stc=1
  14. Replies
    46
    Views
    5,599

    You currently have a stage 3 FZR with a SVHO...

    You currently have a stage 3 FZR with a SVHO engine and you're considering downsizing to a three cylinder engine and then adding a stage 3 kit?
    I would recommend riding a modified GP1800 prior to...
  15. Replies
    75
    Views
    7,435

    HOW MANY HOURS ARE ON YOUR SPARK PLUGS? I had...

    HOW MANY HOURS ARE ON YOUR SPARK PLUGS?

    I had similar issues with my Greenhulk stage 2, MapX, aggressive tune GP1800 for 2nd half of summer, eventually only getting up to 8500rpms and getting...
  16. I was contemplating another location but after...

    I was contemplating another location but after thinking about it I installed mine exactly where Riva recommended. You will need to disassemble the exhaust exit but that's pretty easy, any other...
  17. Wow, that really sucks, sorry to hear it....

    <br>

    Wow, that really sucks, sorry to hear it. That is some serious cracking of the hull going on. Yamaha really seems to have missed something here, they need to redesign or reinforce that area...
  18. Try to wrap the plates in wax paper and set them...

    Try to wrap the plates in wax paper and set them onto the fresh fiberglass work, remove following day and you'll have a perfectly flat surface with no sanding required. page 28 this thread. I prefer...
  19. Not to many people are discussing this lately but...

    Not to many people are discussing this lately but I'm still glad I did mine "page 28", #276 just makes sense to me as it seems to be a potential issue, especially at increased speeds!
  20. Replies
    51
    Views
    16,190

    Sticky: Can also fill the intake grate with an epoxy...

    Can also fill the intake grate with an epoxy filler and retain the factory rubber strip, then seal it up with silicone, it really helped with cavitation. Transom leaking small amounts of water into...
  21. Replies
    86
    Views
    8,386

    I prefer to put it in the water and let it get...

    I prefer to put it in the water and let it get warmed up a bit, make sure the ski is level, then just let it idle for 30 seconds, shut it off and wait one minute, now check the oil. If you add or...
  22. Decided against using Marinetex? Why use an...

    Decided against using Marinetex? Why use an aluminum plate as a filler? It seems like it's elevating the red ultramax plate pretty high off the liner. You really need some good bond in that depressed...
  23. Replies
    7
    Views
    4,261

    Thanks for the awesome pics and explaining to...

    Thanks for the awesome pics and explaining to people how to resolve this issue.
  24. Replies
    6
    Views
    1,026

    http://www.greenhulk.net/forums/attachment.php?att...

    http://www.greenhulk.net/forums/attachment.php?attachmentid=416345&stc=1Rule 500GPH fully automatic pump siliconed in place. Flip toggle switch to on before each ride and have a nice...
  25. I use my mirrors to see who's trying to catch me,...

    I use my mirrors to see who's trying to catch me, also useful in 5mph zones or cruising. I'll keep 'em.
Results 1 to 25 of 40
Page 1 of 2 1 2