Search

Type: Posts; User: rcrisafulli

Page 1 of 8 1 2 3 4

Search: Search took 0.21 seconds.

  1. That is what I thought. I am not a fan of the...

    That is what I thought. I am not a fan of the newer model and I own one. Probably would not buy another one.

    Robert
  2. 2019 FX Cruiser SVHO and CandooPro speedo

    Anyone running this setup? Does the dash read correctly at all speeds?

    Robert
  3. Replies
    7
    Views
    192

    Too rich at idle. Get tuner to lean out a little...

    Too rich at idle. Get tuner to lean out a little at a time.

    Robert
  4. Replies
    7
    Views
    318

    https://www.whelansmarina.com/ He is the...

    https://www.whelansmarina.com/

    He is the bigger seller of our skis on the east coast. They will give the best deal. Call them.

    Robert
  5. Replies
    18
    Views
    1,004

    I am going to make one/adapt one for my 2019. If...

    I am going to make one/adapt one for my 2019. If a vendor comes out with a good one they will sell. It can be a very wet ride at times.

    Robert
  6. Replies
    6
    Views
    217

    You need to check the lash and adjust as need. ...

    You need to check the lash and adjust as need. Check each lobe not just one or two.

    Robert
  7. Replies
    11
    Views
    411

    I built a rig to degree cams on one of my motors....

    I built a rig to degree cams on one of my motors. The motor was out on a stand so it is actually not that difficult of a setup. You need to remove the coupler and put a degree wheel there. You can...
  8. Replies
    11
    Views
    411

    If you can get a F2 for $350 and its perfect, I...

    If you can get a F2 for $350 and its perfect, I would not bother with the 20 psi wheel. I have been running the F2 since 2016. Save your money or put the difference into another mod.

    Robert
  9. That sensor do not give a full range of oil...

    That sensor do not give a full range of oil pressure. It is just a low pressure switch.

    Robert
  10. Thread: Vxr cams

    by rcrisafulli
    Replies
    11
    Views
    572

    Can not go wrong with the et20. New design is...

    Can not go wrong with the et20. New design is probably better then my old 19.

    Robert
  11. The stock ECU does not read oil pressure or fuel...

    The stock ECU does not read oil pressure or fuel level unfortunately.

    Robert
  12. Thread: Vxr cams

    by rcrisafulli
    Replies
    11
    Views
    572

    I would not bother with the VXR cams. I would...

    I would not bother with the VXR cams. I would run the 20 psi wheel and the stock cams. You can advance the intake 2 degrees if you want more bottom end.

    After modding the hell out of these skis...
  13. Replies
    190
    Views
    23,850

    4-Stroke Fired up ski on pump gas and Motec today. Built a...

    Fired up ski on pump gas and Motec today. Built a map from the base GP 1800 package. All holes lite 11.8 afr. Need to review recorded data and lean out. Going to get afr to 13.8 and break motor...
  14. Replies
    190
    Views
    23,850

    4-Stroke Fired up ski today on stock ECU. Good oil...

    Fired up ski today on stock ECU. Good oil pressure and all holes firing. Ski had old Q16 racing fuel. Drained it and need to flush out with pump gas. Have not decided on final configuration may...
  15. Replies
    190
    Views
    23,850

    4-Stroke I have been working on the ski and its almost...

    I have been working on the ski and its almost ready to fire up. All that is left is to put on the exhaust manifold. I am changing some fittings on the oil pressure switch and super charger feed. I...
  16. Replies
    1
    Views
    160

    I took apart another ski to verify. I had it...

    I took apart another ski to verify. I had it right after all.

    For reference, order is small oil cover, spring, relief valve, bullet end towards the gas tank. The spring sits around the bullet...
  17. Replies
    1
    Views
    160

    Oil pressure relief valve

    This is probably a stretch but does anyone remember the order of the oil pressure relief valve and spring. This in under the small cover on the front of the oil pump.

    I took mine a part and...
  18. Md is on lockdown so I can not go work on my skis...

    Md is on lockdown so I can not go work on my skis at another shop I have. We will be lucky to ski in July.

    Robert
  19. Replies
    190
    Views
    23,850

    4-Stroke Yes. Robert

    Yes.

    Robert
  20. Replies
    190
    Views
    23,850

    4-Stroke Maryland is on lock down. No more working on my...

    Maryland is on lock down. No more working on my skis. I have a 5000 sq ft shop at my brothers house. Not supposed to leave my house now. Sucks. I wanted to get this ski running.

    At least, I...
  21. Replies
    18
    Views
    871

    You should check the valve lash to rule it out. ...

    You should check the valve lash to rule it out. I know its a pain.

    Robert
  22. Replies
    190
    Views
    23,850

    4-Stroke Motor has been primed and dropped in the ski. ...

    Motor has been primed and dropped in the ski. Just need to button everything up and get it ready to be fired up.

    Robert
  23. I bought it off this site. Put a wanted ad in...

    I bought it off this site. Put a wanted ad in the for sale section. You should be able to get a used working one off this site. I see a used one for $700 on ebay right now.

    Robert
  24. I have two 2016 FX Cruiser SVHOs. I...

    I have two 2016 FX Cruiser SVHOs. I swapped/stole the TB from the other ski which the motor is out right now. I bought a "new" SVHO TB on the form for 1/3 the cost. It has a different part number...
  25. Replies
    32
    Views
    1,660

    I happen to have an O2 heat sink bung extender in...

    I happen to have an O2 heat sink bung extender in my shop. Benefit of having and working on drag race cars. You can get them online for around $90. My friend has another laying around his shop. I...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4