Search

Page 1 of 2 1 2

Search: Search took 1.00 seconds.

  1. Replies
    29
    Views
    2,581

    I have all the stuff to convert a 15f to ultra lx...

    I have all the stuff to convert a 15f to ultra lx electronics. The missing link is the fuel sender. I'm gonna try to disassemble an old one and report back lol.
  2. I felt this, in my soul. The PO repair looks...

    I felt this, in my soul.

    The PO repair looks like a real POS. Your stuff is looking really nice!
  3. Replies
    107
    Views
    9,194

    The splines fit the early VX110 pump, the one...

    The splines fit the early VX110 pump, the one that is built like a kawasaki and seadoo without the driveshaft attached. Source: Me! I used the spline tool to swap an impeller and it fit nice and...
  4. Replies
    13
    Views
    1,653

    I personally always wanted to put a valve on it...

    I personally always wanted to put a valve on it and a nozzle on the handlebars so i could use it as a giant squirt gun.
  5. Replies
    13
    Views
    1,653

    Its direct from the pump output. So water goes in...

    Its direct from the pump output. So water goes in the pump and out the nozzle. Gay spray is tapped from the reduction nozzle area.
  6. Replies
    12
    Views
    1,139

    The trailer should NOT be nose up. How light is...

    The trailer should NOT be nose up. How light is your trailer tongue? Tongue weight and levelness is important. If you have never had a trailer go crazy due to balance and geometry being off its hard...
  7. ^^^ this My issue with the design is the...

    ^^^ this

    My issue with the design is the replacement part is freaking expensive for what it is. I mean, I know it sounds whiney bitch of me, but that manifold should NOT cost 100+ bucks.
  8. Nah. Then we will have fusion reactor gas threads...

    Nah. Then we will have fusion reactor gas threads because that's the only way the energy density will ever be there.
  9. Replies
    22
    Views
    1,330

    moneypit 1, moneypit 2, moneyabyss, and...

    moneypit 1, moneypit 2, moneyabyss, and WTFmywalletisempty
  10. The FXHO is gonna be a better choice here.

    The FXHO is gonna be a better choice here.
  11. Replies
    13
    Views
    951

    These are the kind of builds I like hearing...

    These are the kind of builds I like hearing about.

    So far I in mine I am most likely going 260x pistons, upgraded pump and regulator setup, wide band setup, and possibly a one step smaller pulley...
  12. Replies
    6
    Views
    839

    i would have no problems buying a 200+ hour ski....

    i would have no problems buying a 200+ hour ski. If it was a yamaha. #shotsfired.
  13. you really wont know until you are in there. it...

    you really wont know until you are in there. it can damage the rod bearings, case, and stator cover bearing as well.
  14. Replies
    3
    Views
    435

    I have one of those intakes to put non CV Polaris...

    I have one of those intakes to put non CV Polaris carbs on my Ultra.
  15. Did they do the pump upgrade on the Ultra. You...

    Did they do the pump upgrade on the Ultra. You should really have that done. Its all fun and games until it lunches the crank due to the pump dying. And you wont feel or hear anything until its too...
  16. Replies
    80
    Views
    7,084

    Having just acquired a 250x I am intrigued by...

    Having just acquired a 250x I am intrigued by what is the simplest/cheapest way to dump the ecu to post.
  17. Replies
    22
    Views
    2,206

    It leaks because cooling water gets dumped in...

    It leaks because cooling water gets dumped in there and it collects and seeps out of the hole. Weld the crap out of it, free up the rings on the stinger in their grooves and rock and roll.
  18. looking closer at the model. that thing will be a...

    looking closer at the model. that thing will be a real biotch to print. You will need to turn supports on. I would probably redo the model with a "snappable" support structure integrated into the...
  19. Replies
    80
    Views
    7,084

    I would like to see the fuel and timing tables...

    I would like to see the fuel and timing tables that are extracted from the bins. I think it would be a good start to baseline a speeduino setup.
  20. Put a 1.8 in it. If you gotta find an engine...

    Put a 1.8 in it. If you gotta find an engine anyway. Everyone needs a second mortgage conversion ski project.
  21. Replies
    9,294
    Views
    524,570

    mmmm CZ love

    mmmm CZ love <3
  22. that isnt bad work for someone who is totally new...

    that isnt bad work for someone who is totally new at this. next thing you know you will be doing a pump tunnel swap on a standup and flat decking X2 hulls :D
  23. trampoline frame halves on end + emt between...

    trampoline frame halves on end + emt between where the legs went + plastic = portable paint booth
  24. looks like typical rental ski damage. No biggie....

    looks like typical rental ski damage. No biggie. Personally I would seal up the backside of that issue up front below the rub rail, pour two part foam in there, sculpt with an air file, then glass...
  25. Replies
    13
    Views
    773

    I am solidly in the latter group. But atleast...

    I am solidly in the latter group. But atleast this way I have no money for drugs. :facepalm::facepalm:
Results 1 to 25 of 36
Page 1 of 2 1 2