Search

Type: Posts; User: Dave in DE

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    191

    Don't know what the difference is between those...

    Don't know what the difference is between those plugs and what should be. But BR8HS/B8HS is what's list for your ski. The R being a resister plug.
  2. Rc239, To get to the insert thats turning...

    Rc239,
    To get to the insert thats turning you'll have to remove the battery and battery compartment box. Then remove the exhaust from below the battery box to get to the floor of the ski. You may...
  3. Replies
    3
    Views
    308

    You'll find it behind the metal plate pictured on...

    You'll find it behind the metal plate pictured on the front of the carbs just off the end of the air box. right behind the square hole. You can reach it from below with finger tips or through the...
  4. Thread: Knee Brace

    by Dave in DE
    Replies
    2
    Views
    410

    Stx-di, I feel for ya. Was there 2 yrs ago with...

    Stx-di, I feel for ya. Was there 2 yrs ago with left knee. May have meniscus tear in right now.
    Never wore a brace, although I'm sure it probably would have helped. I suppose any of the...
  5. Replies
    2
    Views
    312

    I would do the wave eater clips/links when you...

    I would do the wave eater clips/links when you rebuild. That being said. At 115 hrs it's a possibility that it has not been rebuild before. So you may still have nikasil coated cyl. 95/100 psi for...
  6. I used a valve. As stated above it's much easier...

    I used a valve. As stated above it's much easier to get to and operate on the water than finding a clamp and installing.
    The valve I used is small and compact. Found it on Home Depot's web site,...
  7. Replies
    2
    Views
    413

    Thanks, HDAV. Was leaning towards the hydro turf...

    Thanks, HDAV. Was leaning towards the hydro turf as I like the 3m adhesive they use. I ordered samples last night.
  8. Replies
    2
    Views
    413

    Traction mats?

    Looking to replace my GPr mats.

    Who out there makes the best/better traction mats and where can I find them?
    My winter project.
    Thanks,
  9. There are a couple of apps that will find local...

    There are a couple of apps that will find local ethenol free fuel. I use one called "Pure gas" and there are others. There very helpful especially if traveling an unfurmilure area.

    The app gives...
  10. Replies
    2
    Views
    424

    Scoober, on the 650/700 motor the flush hose...

    Scoober, on the 650/700 motor the flush hose screws into the exhaust. On the exhaust there is a plug screw (#16 in pic) that needs to be removed and flush hose installed there. Looking at the ski...
  11. Amsoil interceptor is great oil and designed for...

    Amsoil interceptor is great oil and designed for power valve 2 strokes. I run it myself in my GPr. If you become a preferred member you can buy it direct from them very cheep. around $130 for 4...
  12. Replies
    4
    Views
    573

    Call the guys at Impros. They'll get you hooked...

    Call the guys at Impros. They'll get you hooked up with the right impeller.

    455478
  13. Thread: Fxsvho2016

    by Dave in DE
    Replies
    4
    Views
    349

    Check you air filter for motor oil. The slightest...

    Check you air filter for motor oil. The slightest bit of overfill of oil and the air filter can end up soaked in oil from what I've read on here and other sites.
  14. Replies
    2
    Views
    374

    +1, for what Butterbean said. The pumps are...

    +1, for what Butterbean said. The pumps are bulletproof. It's the lines to the carbs that are the issue. That's a variable mix ratio pump it's mixing 200/1 at idle up to 32/1 at full throttle. It...
  15. Replies
    12
    Views
    647

    A little darkness yes, black no. I can run my...

    A little darkness yes, black no. I can run my GPr for weeks and get a little gray/BLK shading to the white paint in the pump area. Nothing as black as he's talking. The pump does have a fail safe....
  16. Replies
    12
    Views
    647

    You adjust the pump by adjusting the cable end....

    You adjust the pump by adjusting the cable end. Just like you would adjust the the free play in the throttle cable. Shorten or lengthen the cable adjuster till the marks line up.
  17. I don't know of any after market multi's but if...

    I don't know of any after market multi's but if you search the factory Yamaha number on eBay there are some used originals. Just be sure there marked as working and not for parts. The 700 raider # is...
  18. Replies
    12
    Views
    647

    Yes that is the correct cable number. However I'd...

    Yes that is the correct cable number. However I'd check it before ordering. It may have just come loose or off.
    Also when you figure out what is wrong if it's involves the cable you'll need to set...
  19. Replies
    12
    Views
    647

    A little darkness is normal from the oil. but...

    A little darkness is normal from the oil. but based on what your saying. Poor idle, and soot. I'd say it's time to rebuild the carbs and at the same time replace the oil injection lines from the pump...
  20. Replies
    3
    Views
    691

    2-Stroke There still available new from Babbittsonline for...

    There still available new from Babbittsonline for $560 something. There is at least one on eBay. Search it by Yamaha and part number and by yr, model, multi function meter or guage.

    453098
  21. Replies
    1
    Views
    442

    Ya, I'd pull it and replace. If there's been no...

    Ya, I'd pull it and replace. If there's been no damage done then your good to go.
  22. Replies
    15
    Views
    939

    Lube the new filter seal with fresh oil turn it...

    Lube the new filter seal with fresh oil turn it on till it contacts the surface. Then turn it another 1/2 to 3/4 turn. That's more than tight enough. Most times you won't need a wrench to remove...
  23. Replies
    5
    Views
    311

    I'm with myself. Check your mid shaft brgs.

    I'm with myself. Check your mid shaft brgs.
  24. Replies
    32
    Views
    2,026

    Sorry, it's the 3rd sticky down in the Yamaha how...

    Sorry, it's the 3rd sticky down in the Yamaha how to's. Drilled carb return, fuel pressure Ballance. Only difference is you need an 87.5 main jet for the return line for the 800. The recipe is...
  25. If all is correct with fresh motor, clean carbs,...

    If all is correct with fresh motor, clean carbs, it should easily start on the choke with no need for a primer.
    I would start with a compression test. Just because it's a fresh motor doesn't...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4