Search

Type: Posts; User: Jonesyfxr

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    819

    Any updates? I sent you a PM regarding the...

    Any updates?
    I sent you a PM regarding the epoxied intake crossovers
  2. Replies
    3
    Views
    113

    So I called Watercraft Superstore tech line the...

    So I called Watercraft Superstore tech line the other day. They said I ordered the right ones, they’re just a tad smaller than stock but they use them all the time without issues.
  3. Replies
    3
    Views
    115

    You’re on the right track. drill the returns...

    You’re on the right track.
    drill the returns now... it’s easier. We just drilled ours, literally minutes ago. I taped the other passages to prevent shavings from getting all over.
  4. I surely will, I have to research if we would...

    I surely will, I have to research if we would need to re-jet after doing this mod.
  5. Would I have to re-jet to make this mod work??

    Would I have to re-jet to make this mod work??
  6. I agree, this looks like water back filling the...

    I agree, this looks like water back filling the exhaust and filling the cylinders.
  7. Replies
    1
    Views
    76

    The oil in exhaust is normal. As for the smoke...

    The oil in exhaust is normal. As for the smoke being white, are you sure it's not just steam? This is also normal when the ski gets warm.

    What 2 stroke oil are you running?
  8. Replies
    3
    Views
    113

    I’m just wondering if I ordered the wrong ones? ...

    I’m just wondering if I ordered the wrong ones?
    I’ll have to double check what I bought.
  9. From what I understand, you get a better carb...

    From what I understand, you get a better carb signal per cylinder.
  10. Replies
    19
    Views
    601

    Sam here!!! I still have to pressure test our...

    Sam here!!! I still have to pressure test our ski, but think we found part of the issue, as the return orifice was completely blocked in one carb.
  11. Glad you figured it out.

    Glad you figured it out.
  12. Replies
    3
    Views
    113

    Mikuni fuel pump check valve diameter

    So we were rebuilding the last carb for our GPR. I picked up extra fuel pump nipples (cuz we all know how much they suck) and extra check valve disks. I noticed the ones I picked up are about 1mm...
  13. Replies
    2
    Views
    99

    WTB I know there’s some available on EBay... but be...

    I know there’s some available on EBay... but be careful, I ordered a set and had to return them.
  14. Love it!

    Love it!
  15. Replies
    11
    Views
    359

    Oside Bll had a mention of checking the needle...

    Oside Bll had a mention of checking the needle arm height.
  16. I was thinking about using West Systems Six10 two...

    I was thinking about using West Systems Six10 two part epoxy applied with a mixing tip.
  17. Replies
    19
    Views
    601

    DAMN!!!

    DAMN!!!
  18. Replies
    5
    Views
    257

    See if you can align the tubing onto the...

    See if you can align the tubing onto the through-hull and use a paint pen to draw alignment lines on both pieces. Then pull the through-hull off, install the tubing and clamp, slide through the hull...
  19. Replies
    17
    Views
    775

    We acquired an 800 grate for ours. Over Memorial...

    We acquired an 800 grate for ours. Over Memorial weekend I went out and the lake was busy AF. Granted, it’s a tight chop, but I was wide open in 1-2 footers and the pump never unloaded. Needless to...
  20. Replies
    7
    Views
    258

    Start it up and you’ll see what we’re talking...

    Start it up and you’ll see what we’re talking about.
  21. Replies
    7
    Views
    258

    That’s the exhaust

    That’s the exhaust
  22. Thanks Adam.... I figured it had something to do...

    Thanks Adam.... I figured it had something to do with carb signal.
    Any photos or tutorials on how to do this mod?
  23. Replies
    53
    Views
    2,410

    We are using the stock 1200R intake. Everything...

    We are using the stock 1200R intake. Everything bolts right up.
  24. Replies
    53
    Views
    2,410

    We used the 1300 reed plates and reeds. I believe...

    We used the 1300 reed plates and reeds. I believe the reeds are the same.
    We obtained the reed plates from a GH member.
  25. Replies
    53
    Views
    2,410

    We stuck with stock, at least for now.

    We stuck with stock, at least for now.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4