Search

Page 1 of 2 1 2

Search: Search took 1.00 seconds.

  1. Got the cable today, finally finished my 2018+...

    Got the cable today, finally finished my 2018+ harness to read/write FW. Too bad Yamaha stopped using the 3-pin diagnostic in YDS. I can only use the 26-pin on 2009-2014 models.

    ...
  2. Replies
    26
    Views
    2,162

    Engine back together now, just need to drop it...

    Engine back together now, just need to drop it back in the ski.
    I decided to make a table lamp out of one of the old pistons
    457081
  3. Replies
    81
    Views
    14,068

    Guys, I just heard back from my contact with...

    Guys, I just heard back from my contact with Yamaha. If you measure across the back of the pump where the venturi nozzle mounts up you will see that it's 160mm. Older pumps were 155, and their 2020...
  4. You are correct. The SVHO is safe with the stock...

    You are correct. The SVHO is safe with the stock valve train to 8650. Any higher than that and you need retainers.
  5. Replies
    11
    Views
    916

    Splitting hairs but the stock retainers should be...

    Splitting hairs but the stock retainers should be good for 8650 rpms I thought.
  6. Speaking of fuel, its so stupid on the 2018...

    Speaking of fuel, its so stupid on the 2018 GP1800 to have 8 bar levels for fuel, but it goes in increments of 2 bars. what a horse shit design.
    I just got down to 1/2 tank yesterday as we were...
  7. Replies
    11
    Views
    1,383

    Yes yes yes. I just did deans transom plate...

    Yes yes yes. I just did deans transom plate and we resealed eveything. Now there is basically zero cavitation. I think we improved pump efficiency so much that i am going to remove some spacers...
  8. Replies
    5
    Views
    879

    I assume your on a GP1800, your sig shows a doo. ...

    I assume your on a GP1800, your sig shows a doo. So many factors, water conditions, how well your hooked up. Trim position. ETC.

    You say dusted, like close, even, or he was just gone. My ski...
  9. I think you should do like hurricane suggested...

    I think you should do like hurricane suggested load a different tune and see if that is the problem do a stage 1 8500 and see where your at that's very low rpms with that prop
  10. View Post

    Where are you located? I’d love to help you for FREE!!!!!!!!!!

    you need two bars on the left do you can work both functions...
  11. Thread: Tial 50 mm BOV

    by badjoka
    Replies
    26
    Views
    2,538

    Sorry, Not sure how it works, but seems to work...

    Sorry, Not sure how it works, but seems to work well and haven't had any issues with it.
  12. Replies
    5
    Views
    1,207

    what did we do in the days before the internet???...

    what did we do in the days before the internet??? i searched for 159 and found that if any blocks the basket from lowering when starting it will read 159, my tie town strap was blocking, wow what a...
  13. So I took the big 3 seater out tonight......

    And I am super happy!!


    So I don't know what Stage it is, since I have the 17 lb. wheel. So you tell me.

    Stage 3 tune
    17lb wheel with R&D shaft
    Riva Super cooler with HKS
    1000cc injectors...
  14. View Post

    Find out soon!

    About to do a shootout between the new 2018 Seadoo RXT-X and Yamaha GP1800 with Kevin Shaw of The Watercraft Journal. We will be using the super accurate VBox Sport to measure...
  15. Well that makes sense then.

    Well that makes sense then.
  16. Replies
    52
    Views
    16,851

    A bad day on the water, always beats a good day...

    A bad day on the water, always beats a good day in the office
  17. Thread: No Boost

    by not2fast
    Replies
    7
    Views
    629

    That is what I thought. I tightened until it...

    That is what I thought. I tightened until it wouldn't move. I think I should be good now.
  18. Replies
    47
    Views
    9,829

    No, I did not. Stock GP nozzle is 87mm. I...

    No, I did not. Stock GP nozzle is 87mm. I wouldn't go any bigger than that. If anything try smaller nozzle like the 85mm.
  19. Replies
    4
    Views
    443

    Buy one with a tune from Deans Team. Available...

    Buy one with a tune from Deans Team. Available here in the store
  20. Replies
    23
    Views
    1,820

    I'm jealous, I want to be on the water; and it...

    I'm jealous, I want to be on the water; and it does look like a good day, and then you went and spoiled it with a lite beer! Lol. I'm IPA all the way:lol:
  21. Finally had some time to work on this thing...

    Finally had some time to work on this thing again. Got the pump installed,along with the Shred master ride plate and Worx intake grate. Bolted the new handle bars up, installed the aggressor...
  22. Replies
    20
    Views
    1,962

    Thanks for posting this!! My ski has icicles on...

    Thanks for posting this!! My ski has icicles on it yesterday this winter has SUCKED!!!
  23. Replies
    11
    Views
    2,100

    sadly.... produce a better ski and nature...

    sadly.... produce a better ski and nature produces a bigger idiot to break the skies LoL
  24. No offense, but if I stopped doing builds and...

    No offense, but if I stopped doing builds and projects everytime someone told me I couldn't use something because it wasn't made for that, I would never have done most of the fabricating or builds...
  25. The part number of the stuffer is 13070-3715.

    The part number of the stuffer is 13070-3715.
Results 1 to 25 of 27
Page 1 of 2 1 2